10G USB 3.2 Re-timer (1-Port)

Features * Built-in re-timer ㅡ Integrated re-timer for USB 3.2 1-port (Tx/Rx) up to 10Gbps ㅡ Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re- * timer (BLR) Architectures of USB3.1 Specification (Appendix-E) ㅡ 1055 compensation to recover up to 23dB channel loss

文件：668.15 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

10G Active Redriver with Linear Equalization for USB3.2/DisplayPort™

Features • Built-in redrivers − Integrated re-driver for USB3.2 up to Gen 2 @ 10Gbps − Integrated re-drivers for DisplayPort up to UHBR10 @ 10Gbps. − Supports both host (source) and device (sink) applications in USB-C subsystems with DisplayPort Alternate Mode − Loss compensation to recover u

文件：254.72 Kbytes 页数：3 Pages

ANALOGIX

硅谷数模

6G Active Re-driver with Linear Equalization for HDMI 2.0

Features • Built-in Re-driver with CTLE − Integrated Re-driver for HDMI2.0 up to 6Gbps − Supports DP++, HDMI Source applications − Loss compensation to recover up to -10dB channel loss @6Gbps • CTLE, Flat Gain and Swing configurations − Four-lane configurations set by pin strapping. − Indep

文件：223.57 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

8.1G (up to HBR3) DisplayPort™ 4-lane Re-timer

Features  Built-in re-timers − Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps. Supports both transparent mode and non-transparent mode (transparent or LTTPR) − Loss compensation to recover up to 27dB  Integrated AUX pass-through − Integrated A

文件：220.8 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

12G Active Redriver with Linear Equalization for HDMI 2.1

Features  Built-in CTLE redrivers - Independent channel configuration - Loss compensation to recover up to -12dB channel loss @ 12Gbps  Four lanes of HDMI 2.1 up to 12Gbps - Supports DP++  Serial and debug interfaces - I2C Slave interface, up to 1MHz, for redriver configuration  Indust

文件：370.48 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

10G USB 3.1 Re-timer (1-Port)

Features
Built-in re-timer - Integrated re-timer for USB 3.1 1-port (Tx/Rx) up to 10Gbps - Loss compensation to recover up to 23dB channel loss
Protocol awareness for better link power management (LPM) and savings
Reference clock for re-timer - Utilizes a 24MHz reference XTAL or 1.05V

文件：204.54 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

10G Active Mux (1x2) with Integrated Re-timer for USB 3.1

Features
Built-in re-timer - Integrated re-timer for USB 3.1 up to Gen 2 @ 10Gbps - Loss compensation to recover up to 23dB channel loss
Integrated mux - Digital (1x2) mux switches USB signals and preserves enhanced signal output over USB-C connector - Mux control input through I2C comma

文件：221.29 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

8.1G DisplayPort™ 4-lanes Re-timer

Features  Built-in re-timers - Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps - Supports both transparent mode and nontransparent mode (transparent or LTTPR) - Loss compensation to recover up to 27dB channel loss  Integrated AUX pass-through

文件：211.29 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模

SlimPort® (4K Ultra-HD) Receiver

Features * Standard compliance - DisplayPort1.4, HDCP2.2/1.4 - MIPI-DSI 1.2 and D-PHY 1.1 * DisplayPort Receiver - DisplayPort1﹒4 receiver - Configurable 1, 2 or 4-lane input supports: HBR3 (8.1Gbps), 1882 (5.4Gbps), HBR (2.7Gbps) and RBR (1.62Gbps) - Horizontal left / right line splitting

文件：861.89 Kbytes 页数：3 Pages

ANALOGIX

硅谷数模

10G USB 3.2 Re-timer (1-Port)

Features * Built-in re-timer ㅡ Integrated re-timer for USB 3.2 1-port (Tx/Rx) up to 10Gbps ㅡ Supports both Separate Reference Clock Independent SSC (SRIS) and Bit-Level Re- * timer (BLR) Architectures of USB3.1 Specification (Appendix-E) ㅡ 1055 compensation to recover up to 23dB channel loss

文件：668.15 Kbytes 页数：2 Pages

ANALOGIX

硅谷数模