Surface strain sensor Highly sensitive, -600 … 600 με

• Very high measuring sensitivity even minute forces can be accurately measured. • Because of its low acceleration sensitivity also suitable for measurements on moving parts. • Measuring range for tensile and compression forces. • Extremely simple installation as sensor is secured with only

文件：366.18 Kbytes 页数：3 Pages

KSL

Surface strain sensor Highly sensitive, -600 … 600 με

• Very high measuring sensitivity even minute forces can be accurately measured. • Because of its low acceleration sensitivity also suitable for measurements on moving parts. • Measuring range for tensile and compression forces. • Extremely simple installation as sensor is secured with only

文件：366.18 Kbytes 页数：3 Pages

KSL

PinSens Force Sensor for mold cavity pressure with diameter 12,6 mm

• Replaceable cable • Available with single-wire technology

文件：529.07 Kbytes 页数：5 Pages

KSL

PinSens Force Sensor for mold cavity pressure with diameter 12,6 mm

• Replaceable cable • Available with single-wire technology

文件：529.07 Kbytes 页数：5 Pages

KSL

Longitudinal Measuring Pin M5 for contactfree measurement of cavity and injection pressures

• Compact installation size • Contact-free measurement of high pressures • Cavity pressure measurement behind the cavity wall, without imprint • Indirect measurement of injection pressure in the nozzle

文件：573.48 Kbytes 页数：5 Pages

KSL

3-Component Measuring System For cutting force measurement during turning

• Machine adapters for disk-type turrets with: – VDI tool holding fixtures ø30 mm, ø40 mm, ø50 mm – Coromant Capto C5, C6 clamping unit – Direct tool holding fixtures 20x40 mm, 25x50 mm, ¾x1½, 1x2 • Tool holders for external turning tools: 20x20 mm, 25x25 mm, ¾x¾, 1x1 • Tool holders for int

文件：1.59543 Mbytes 页数：12 Pages

KSL

3-Component Measuring System For cutting force measurement during turning

• Machine adapters for disk-type turrets with: – VDI tool holding fixtures ø30 mm, ø40 mm, ø50 mm – Coromant Capto C5, C6 clamping unit – Direct tool holding fixtures 20x40 mm, 25x50 mm, ¾x1½, 1x2 • Tool holders for external turning tools: 20x20 mm, 25x25 mm, ¾x¾, 1x1 • Tool holders for int

文件：1.59543 Mbytes 页数：12 Pages

KSL

3-Component Measuring System For cutting force measurement during turning

• Machine adapters for disk-type turrets with: – VDI tool holding fixtures ø30 mm, ø40 mm, ø50 mm – Coromant Capto C5, C6 clamping unit – Direct tool holding fixtures 20x40 mm, 25x50 mm, ¾x1½, 1x2 • Tool holders for external turning tools: 20x20 mm, 25x25 mm, ¾x¾, 1x1 • Tool holders for int

文件：1.59543 Mbytes 页数：12 Pages

KSL

3-Component Measuring System For cutting force measurement during turning

• Machine adapters for disk-type turrets with: – VDI tool holding fixtures ø30 mm, ø40 mm, ø50 mm – Coromant Capto C5, C6 clamping unit – Direct tool holding fixtures 20x40 mm, 25x50 mm, ¾x1½, 1x2 • Tool holders for external turning tools: 20x20 mm, 25x25 mm, ¾x¾, 1x1 • Tool holders for int

文件：1.59543 Mbytes 页数：12 Pages

KSL

Surface Strain Transmitter for indirect measurement of process forces

• Easy user-friendly parameter configuration via integral serial interface using ManuWare PC program • Two fully programmable independent measuring ranges (adjustable between ±20 με and ±800 με), switchable under load • Adjustable FSO voltage (±1 ... 10 V), offset voltage (±9 V) and output s

文件：551.73 Kbytes 页数：5 Pages

KSL