MSP430G2201

具有 2KB 闪存、128B SRAM 和计时器的 16MHz MCU; • Low Supply-Voltage Range: 1.8 V to 3.6 V\n• Ultralow Power Consumption \n• Active Mode: 220 µA at 1 MHz, 2.2 V\n• Standby Mode: 0.5 µA\n• Off Mode (RAM Retention): 0.1 µA\n \n• Five Power-Saving Modes\n• Ultrafast Wake-Up From Standby Mode in Less Than 1 µs\n• 16-Bit RISC Architecture, 62.5-ns Instruction Cycle Time\n• Basic Clock Module Configurations \n• Internal Frequencies up to 16 MHz With One Calibrated Frequency\n• Internal Very Low Power Low-Frequency (LF) Oscillator\n• 32-kHz Crystal\n• External Digital Clock Source\n \n• 16-Bit Timer_A With Two Capture/Compare Registers\n• Brownout Detector\n• On-Chip Comparator for Analog Signal Compare Function or Slope A/D (See )\n• Serial Onboard Programming, No External Programming Voltage Needed, Programmable Code Protection by Security Fuse\n• On-Chip Emulation Logic With Spy-Bi-Wire Interface\n• Available in a 14-Pin Plastic Small-Outline Thin Package (TSSOP) (PW), 14-Pin Plastic Dual Inline Package (PDIP) (N), and 16-Pin QFN (RSA);

The Texas Instruments MSP430 family of ultralow-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 µs. The MSP430G2x01 and MSP430G2x11 series is an ultralow-power mixed signal microcontroller with a built-in 16-bit timer and ten I/O pins. The MSP430G2x11 family members have a versatile analog comparator. Typical applications include low-cost sensor systems that capture analog signals, convert them to digital values, and then process the data for display or for transmission to a host system.

MSP430G2201

MIXED SIGNAL MICROCONTROLLER

MSP430G2201

ULTRA-LOW-POWER MICROCONTROLLERS

MSP430G2201

MSP430G2553 LaunchPad??Development Kit

MSP430G2201-Q1

具有 2KB 闪存、128B SRAM 和计时器的汽车类 16MHz MCU; • 符合汽车应用要求\n• 低电源电压范围：1.8V 至 3.6V\n• 超低功耗 \n• 激活模式：220μA（在 1MHz 频率和 2.2V 电压条件下）\n• 待机模式：0.5μA\n• 关闭模式（RAM 保持）：0.1μA\n \n• 5 种节能模式\n• 可在不到 1μs 的时间里从待机模式唤醒\n• 16 位精简指令集 (RISC) 架构，62.5ns 指令周期时间\n• 基本时钟模块配置 \n• 具有一个校准频率并高达 16MHz 的内部频率\n• 内部超低功率低频 (LF) 振荡器\n• 32kHz 晶振\n• 外部数字时钟源\n \n• 具有 2 个捕捉/比较寄存器的 16 位 Timer_A\n• 欠压检测器\n• 用于模拟信号比较功能或者斜率模数转换的片上比较器（请参见 ）\n• 串行板上编程， 无需外部编程电压， 利用安全熔丝实现可编程代码保护\n• 具有两线制 (Spy-Bi-Wire) 接口的片上仿真逻辑电路\n• 要获得系列产品成员详细信息，请参见\n• 提供的封装 \n• 14 引脚塑料小外形尺寸薄型封装 (TSSOP)(PW)\n• 16 引脚四方扁平无引线封装 (QFN)(RSA)\n \n• 如需了解完整的模块说明， 请参见 （文献编号：SLAU144）;

德州仪器 (TI) 的 MSP430 系列超低功率微控制器包含几个器件，这些器件特有针对多种应用的不同外设集。 这种架构与 5 种低功耗模式相组合，专为在便携式测量应用中延长电池使用寿命而优化。 该器件具有一个强大的 16 位 RISC CPU，16 位寄存器和有助于获得最大编码效率的常数发生器。 此数控振荡器 (DCO) 可使器件在不到 1µs 的时间内实现从低功率模式唤醒至激活模式。 MSP430G2x01 和 MSP430G2x11 器件包括具有内置 16 位定时器和 10 个 I/O 引脚的超低功率混合信号微控制器。 MSP430G2x11 系列产品成员具有一个多用途模拟比较器。 典型应用包括低成本传感器系统，此类系统负责捕获模拟信号，将之转换为数字值，随后对数据进行处理以进行显示或传送至一个主机系统。

MSP430G2201IN14

MIXED SIGNAL MICROCONTROLLER

MSP430G2201IN14

MIXED SIGNAL MICROCONTROLLER

MSP430G2201IN14

MIXED SIGNAL MICROCONTROLLER

MSP430G2201IN14

MIXED SIGNAL MICROCONTROLLER

MSP430G2201IN14

MIXED SIGNAL MICROCONTROLLER