10-bit GTL Processor Voltage Clamp

Description Within the semiconductor world, there are many I/O standards that have different voltage level requirements for the input voltage (VIH or VIL) and output voltage (VOH or VOL) typically based on the device operating voltage. These voltage levels define how the device communicates with

文件：52.76 Kbytes 页数：6 Pages

PHI

PHI

10-bit GTL Processor Voltage Clamp

Description Within the semiconductor world, there are many I/O standards that have different voltage level requirements for the input voltage (VIH or VIL) and output voltage (VOH or VOL) typically based on the device operating voltage. These voltage levels define how the device communicates with

文件：52.76 Kbytes 页数：6 Pages

PHI

PHI

恩XP bidirectional low-voltage translators

Low cost bidirectional voltage translation without directional control Unlike level-shifting bus switches, which only translate between fixed voltages, these bidirectional low-voltage translators can translate any voltage between 1 and 5 V to any other voltage between 1 and 5 V. They also re

文件：263.32 Kbytes 页数：2 Pages

恩XP

10-BIT BIDIRECTIONAL LOW-VOLTAGE TRANSLATOR

文件：299.46 Kbytes 页数：17 Pages

TI

德州仪器

10位双向低电压变换器

The Gunning Transceiver Logic - Transceiver Voltage Clamps (GTL-TVC) provide high-speed voltage translation with low ON-state resistance and minimal propagation delay. The GTL2010 provides 10 NMOS pass transistors (Sn and Dn) with a common gate (GREF) and a reference transistor (SREF and DREF). The 10-bit bidirectional low voltage translator\nAllows voltage level translation between 1.0 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V buses, which allows direct interface with GTL, GTL+, LVTTL/TTL and 5 V CMOS levels\nProvides bidirectional voltage translation with no direction pin\nLow 6.5 Ω ON-s;

恩XP

10位双向低电压变换器

射型收发器逻辑 - 收发器电压钳位(GTL-TVC)提供低通态电阻和最小传输延迟的高速电压变换。GTL2010提供10个带有共栅(GREF)的NMOS传输晶体管（Sn和Dn）和一个参考晶体管（SREF和DREF）。该器件允许1.0 V和5.0 V之间的双向电压变换而无需使用方向引脚。\n当Sn或Dn端口为低电平时，钳位处于通态且Sn和Dn端口之间存在低电阻连接。假设Dn端口上有更高的电压，当Dn端口为高电平时，Sn端口上的电压限制为参考晶体管(SREF)设置的电压。当Sn端口为高电平时，上拉电阻会将Dn端口上拉至VCC。此功能允许在用户选择的更高和更低电压之间进行无缝变换，而无需方向控制。\n 10位双向低电压变换器\n允许1.0 V、1.2 V、1.5 V、1.8 V、2.5 V、3.3 V和5 V总线（允许直接连接GTL、GTL+、LVTTL/TTL和5 V CMOS电平）之间的电压电平变换\n提供双向电压变换，无方向引脚\n输入和输出引脚(Sn/Dn)之间有低6.5 Ω导通状态阻抗(Ron)\n支持热插入\n无需电源：不会闭锁\n5 V耐受输入\n低待机电流\n直通引出线便于印刷电路板走线排布\nESD保护：按JESD22-A114超过2000 V HBM，按JESD22-A115超过200 V MM，按JESD22-C101超过1000 V CDM\n提供封装：TSSOP24;

恩XP