GPM8F3108A中文资料44-Pin 8-bit Microcontroller with 8KB Flash Memory数据手册Generalplus规格书

描述 Description

The GPM8F3108A is a highly integrated microcontroller which integrates a pipelined 1T 8051 CPU, 256-byte XRAM, 256-byte IDM SRAM and 8K-byte program Flash. It includes 34 programmable multi-functional I/Os, Timer0/1/2, UART0, SPI (master), built-in OP and Comparator, audio and one up to 8-channel of 12-bit ADC for general-purpose application. It operates over a wide voltage range of 2.4V - 5.5V with different clock sources. It has two modes in power management unit. Moreover, there is one on-chip debug circuit with two pins to facilitate full speed in-system debug. The detail is described in the following sections.

特性 Features

• CPU
• High speed, high performance 1T 8051
• 100% software compatible with industry standard 8051
• Pipeline RISC architecture enables to execute instructions 10 times faster than standard 8051
• Up to 24.5MHz clock operation


• Memories
• 256 bytes XRAM
• 256 bytes internal Data Memory (IDM) SRAM
• 32K bytes Flash with high endurance
• Minimum 200,000 program/erase cycles
• Minimum 20 years data retention

• Programming read only level for software security

• Clock Management
• Internal oscillator: 24.5MHz±2% @ 2.4V~5.5V
• External clock input max 24.5MHz
• Crystal input with 32768Hz or 1MHz~25MHz

• Power Management
• 1 STOP mode for power saving
• 1 IDLE mode for only peripheral operation

• Interrupt Management
• 16 interrupt sources
• Up to 6 external interrupt sources

• Reset Management
• Power On Reset (POR)
• Low Voltage Reset (LVR)
• Pad Reset (PAD_RST)
• Watchdog Reset (WDT_RST)
• Software Reset (S/W_RST)
• Stop Mode Reset (STOP_RST)
• Miss Clock Reset (MISS_CLK_RST)
• Flash Related Error Reset (FLASH_ERR_RST)

• Programmable Watchdog Timer
• A time-base generator
• An event timer
• System supervisor

• I/O Ports
• Max. 34 multifunction bi-directional I/Os
• Each incorporate with pull-up resistor, pull-down resistor, output high, output low or floating input, depending on programmer''s settings on the corresponding registers
• I/O ports with 20mA current sink
• I/O ports with 8mA current drive

• Two 16-bit Timer/Counter (Timer 0/1)
• Timer mode with clock source selectable
• Auto reload 8-bit timers
• Externally gated event counters

• One Powerful Timer 2 with 16-bit Compare/Capture Unit
• Timer mode with clock source selectable
• Auto-reload 16-bit timers
• Externally gated event counters
• Event capturing
• Pulse width modulation and measurement

• UART0
• One synchronous mode
• Three asynchronous modes

• SPI (master mode)
• Programmable phase and polarity of master clock
• Programmable master SPI_CLK clock frequency
• Max SPI clock: 6.125MHz (FOSC /4) @24.5MHz

• A/D converter
• One 8-channel 8-bit resolution mode
• One 8-channel 12-bit resolution mode
• Max conversion clock: 6.125MHz (FOSC /4) @24.5MHz

• Motor Control Unit
• Programmable dead-time control
• Built-in protective circuits
• 16-bit capture unit control
• Sine-wave PWM control (only in GPM8F3132A)

• Audio Module
• 24KHz output or 32KHz output @24.5MHz

• Debug Unit