GPM8F1065A数据手册Generalplus中文资料规格书

描述 Description

The GPM8F1065A is a highly integrated microcontroller which integrates a pipelined 1T 8051 CPU, 1.5K-byte XRAM, 256-byte IDM SRAM and 64K-byte program Flash.  It also includes up to 23 programmable multi-functional I/Os, Timer0/1/2, UART0, SPI(master), I2C, and CMDT for general-purpose application.  It operates over a wide voltage range of 1.8V - 5.5V and wide temperature range of -5℃ ~ 70℃.  It has two modes in power management unit.  There is also one on chip debug circuit with two pins to facilitate full speed in-system debug.  The detail is described in the following sections.

特性 Features

• CPU
• High speed, high performance 1T 8051
• 100% software compatible with industry standard 8051
• Pipeline RISC architecture enables to execute instructions 10 times faster than standard 8051

• Up to 16MHz clock operation

• Memory
• 1.5K bytes XRAM
• 256 bytes internal Data Memory (IDM) SRAM
• Up to 64K bytes Flash with high endurance
• Minimum 100K progam/erase cycles
• Minimum 10 years data retention
• Page size 1kB

• Programming lock level for software security



• Clock Management
• Internal oscillator: 16MHz±1.5% @ 2.0V~5.5V
• Crystal input with 1MHz~16MHz

• Slow Clock
• Internal oscillator: 4KHz

• Power Management
• One STOP mode for power saving
• One IDLE mode for only peripheral operation


• Interrupt Management
• Up to 9 internal interrupt sources
• Up to 5 external interrupt sources
• Up to 8 keyboard Interrupt sources

• Reset Management
• Power On Reset (POR)
• Low Voltage Reset (LVR)
• Pad Reset (PAD_RST)
• Watchdog Reset (WDT_RST)
• Software Reset (S/W_RST)
• Stop mode Reset (STOP_RST)
• Miss Clock Reset (MISS_CLK_RST)
• Flash Related Error Reset (FLASH_ERR_RST)

• Programmable Watchdog Timer
• A time-base generator
• An event timer
• System supervisor

• I/O Ports
• Max 23 multifunction bi-directional I/Os

• Each incorporate with pull-up resistor, pull-down resistor, output high, output low or floating input, depending on programmer's settings on the corresponding registers
• I/O ports with 12mA current sink
• I/O ports with 12mA current drive
• Two 16-bit Timer/Counter (Timer 0/1)
• Timer mode with clock source selectable
• Auto reload 8-bit timers

• One Powerful Timer2 with 16-bit Compare/Capture Unit
• Timer mode with clock source selectable
• Auto reload 16-bit timers
• Event capturing
• Digital signals generator
• Pulse width modulation and measurement

• UART0
• One synchronous mode
• Three asynchronous modes

• SPI (master mode)
• Programmable phase and polarity of master clock
• Programmable master clock frequency
• Auto read/write function
• Max SPI clock: 4MHz (FOSC /4) @16MHz

• I2C (master/slave mode)
• Carrier Modulator/Demodulator Timer (CMDT)
• One 8-bit Timer A for carrier generation and detection
• One 16-bit Timer B for envelop generation and detection
• Drives IR_TX pin for remote control communication
• Receive IR signal from IR_RX pin

• Built-in Low Voltage Reset
• Trigger level: 1.9V

• Built-in low Voltage Detect
• Programmable level: 2.3V, 2.5V, 3.3V, 3.5V

• On-chip Debug Unit
• C compatible Development Tools