CC1311P3RF/IF射频/中频RFID的射频收发器IC规格书PDF中文资料

1 Features

Wireless microcontroller

• Optimized 48-MHz Arm® Cortex®-M0+ processor

• 256 KB of in-system programmable flash

• 12 KB of ROM for bootloader and drivers

• 28 KB of ultra-low leakage SRAM. Full RAM

retention in standby mode

• 2.4 GHz RF transceiver compatible with

Bluetooth® 5.3 Low Energy

• Integrated balun

• Supports over-the-air upgrade (OTA)

• Serial Wire Debug (SWD)

Low power consumption

• MCU consumption:

– 2.6 mA active mode, CoreMark®

– 53 μA/MHz running CoreMark®

– < 710 nA standby mode, RTC, 28 KB RAM

– 165 nA shutdown mode, wake-up on pin

• Radio Consumption:

– 5.3 mA RX

– 5.1 mA TX at 0 dBm

– < 11.0 mA TX at +8 dBm

Wireless protocol support

• Bluetooth® 5.3 Low Energy

High-performance radio

• -102 dBm for Bluetooth® Low Energy 125 kbps

• -96.5 dBm for Bluetooth® Low Energy 1 Mbps

• Output power up to +8 dBm with temperature

compensation

Regulatory compliance

• Suitable for systems targeting compliance with

these standards:

– EN 300 328 (Europe)

– FCC CFR47 Part 15

– ARIB STD-T66 (Japan)

MCU peripherals

• 12 I/O Pads

– 2 IO pads SWD, muxed with GPIOs

– 2 IO pads LFXT, muxed with GPIOs

– 8 DIOs (analog or digital IOs)

• 2 × 16-bit general-purpose timers, quadrature

decode mode support

• 12-bit ADC, 1.2 Msps with external reference, 267

ksps with internal reference, 4 external ADC inputs

• 1× low power comparator

• 1× UART

• 1× SPI

• 1× I2C

• Real-time clock (RTC)

• Integrated temperature and battery monitor

• Watchdog timer

Security enablers

• AES 128-bit cryptographic accelerator

• Random number generator from on-chip analog

noise

Development tools and software

• LP-EM-CC2340R5 LaunchPad Development Kit

• SimpleLink™ CC23xx Software Development Kit

(SDK)

• SmartRF™ Studio for simple radio configuration

• SysConfig system configuration tool

Operating range

• On-chip buck DC/DC converter

• 1.71-V to 3.8-V single supply voltage

• Tj: -40 to +85°C

RoHS-compliant package

• 4-mm × 4-mm RGE QFN24 (12 GPIOs)

2 Applications

• Medical

– Home healthcare – blood glucose monitors,

blood pressure monitor, CPAP machine,

electronic thermometer

– Patient monitoring & diagnostics – medical

sensor patches

– Personal care & Fitness – electric toothbrush,

wearable fitness & activity monitor

• Building automation

– Building security systems – motion detector,

electronic smart lock, door and window sensor,

garage door system, gateway

– HVAC – thermostat, wireless environmental

sensor

– Fire safety system – smoke and heat detector

– Video surveillance – IP network camera

• Lighting

– LED luminaire

– Lighting Control – daylight sensor, lighting

sensor, wireless control

• Factory automation and control

• Communication equipment

– Wired networking

– wireless LAN or Wi-Fi access points, edge

router

• Personal electronics

– Connected peripherals – consumer wireless

module, pointing devices, keyboards and

keypads

– Gaming – electronic and robotic toys

– Wearables (non-medical) – smart trackers,

smart clothing

3 Description

The SimpleLink™ CC2340R2 device is a 2.4 GHz wireless microcontroller (MCU) targeting Bluetooth® 5 Low

Energy and Zigbee®. The device is optimized for low-power wireless communication as an entry-level SoC

(system-on-chip) to enable a broad range of end products in categories such as medical, building automation,

beacons, asset tracking, disposables, smart grid and personal electronics. Additionally, the CC2340R2 device

can function as an attached Bluetooth Low Energy network processor (or “data pump”) adding full Bluetooth Low

Energy capability to the main MCU via a serial interface. Highlighted features of this device include:

• Support for Bluetooth ® 5 features: High Speed Mode (2 Mbps PHY), Long Range (LE Coded 125 kbps and

500 kbps PHYs), Privacy 1.2.1 and Channel Selection Algorithm #2, as well as backwards compatibility and

support for key features from the Bluetooth ® 4.2 and earlier Low Energy specifications.

• Fully-qualified Bluetooth ® 5.3 software protocol stack included with the SimpleLink™ CC23xx Software

Development Kit (SDK).

• Zigbee® Green Power protocol stack support in the SimpleLink™ CC23xx Software Development Kit (SDK) 1

• Ultra-low standby current less than 0.71 μA with RTC operational and full RAM retention that enables

significant battery life extension especially for applications with longer sleep intervals.

• Integrated balun for reduced Bill-of-Material (BOM) board layout.

• Excellent radio sensitivity and robustness (selectivity and blocking) performance for Bluetooth ® Low Energy

(-102 dBm for 125 kbps LE Coded PHY, with integrated balun).

• Pin to Pin compatible with CC2340R5 RGE Package.

The CC2340R2 device is part of the SimpleLink™ MCU platform, which consists of Wi-Fi®, Bluetooth Low

Energy, Thread, Zigbee, Sub-1 GHz MCUs, and host MCUs that all share a common, easy-to-use development

environment with a single core software development kit (SDK) and rich tool set. A one-time integration of the

SimpleLink™ platform enables you to add any combination of the portfolio’s devices into your design, allowing

100 percent code reuse when your design requirements change. For more information, visit SimpleLink™ MCU

platform.