ATA6570数据手册集成电路（IC）的驱动器接收器收发器规格书PDF

描述 Description

The ATA6570 is a CAN Partial Networking (PN) transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two wire CAN bus. It is designed for high speed CAN applications in the automotive environment. It provides local and enhanced remote wake-up capabilities. The Microchip ATA6570 has a very low power consumption in Standby and Sleep Mode. Beside local wake-up via WAKE and remote wake-up pattern according to ISO 11898-2: 2016 and also additionally supports ISO11898-2: 2016 compliant CAN partial networking. A CAN frame decoder evaluates the bus traffic and checks for a matching frame, that has been configured in the registers via SPI. The device is able to keep the complete ECU in a low power mode even when bus traffic is present until a valid wake-up frame is received. It also features a watchdog, a Serial Peripheral Interface (SPI) and automatic adjustment of the I/O levels to the I/O level of the connected microcontroller via the VIO pin. The Microchip ATA6570 is a CAN-FD capable device. Wakeup via Wake-up frames can be configured to be either CAN-FD tolerant (CAN-FD frames are ignored) or to increase an error counter when receiving FD frames.The Transceiver also offers Normal, Standby and Silent mode to configure the TX/RX path. This configuration is done via SPI.To purchase the ATA6570 or obtain additional information, please contact any Microchip sales representative or authorized worldwide distributor.Please see our MikroElektronika click Board! https://www.mikroe.com/ata6570-clickAn MCAL driver is available upon request as described here: https://www.microchip.com/en-us/solutions/automotive-and-transportation/softwarePlease contact your local Sales representative.

特性 Features

High speed CAN PN transceiver Fully ISO 11898-2, ISO 11898-5, ISO 11898-2: 2016 and SAE J2962-2 compliant
ISO 26262 FuSa Ready
Autonomous bus biasing according to ISO 11898-6
Low electromagnetic emission (EME) and high electromagnetic immunity (EMI)
Standard CAN data rate up to 1Mbit/s and CAN FD data rate up to 5Mbit/s (CAN FD)
Differential bus receiver with wide common mode range
Very low current consumption in Sleep and Standby with fully wake-up capability
Power-down of the complete node via the INH-output (switching off external voltage regulator(s))
T wake-up sources Local wake-up via pin WAKE Remote wake-up pattern according to ISO 11898-5 Remote wake-up frame according to ISO 11898-6 (selective wake-up) Host wake-up via SPI Wake-up source recognition
Local wake-up via pin WAKE
Remote wake-up pattern according to ISO 11898-5
Wake-up source recognition
3.3V to 5V microcontrollers can be interfaced directly via the VIO pin
Battery supply and CAN bus pins protected against transients according to ISO7637
High Electro Static Discharge (ESD) Handling Capability on the Bus Pins
Bus pins short-circuit protected to GND and VCC
VS operating voltage up to 28V, VS DC supply voltage up to 40V
AEC-Q100 and AEC-Q006 qualified
Fulfills the OEM Hardware Requirements for CAN Interfaces in Automotive Applications, Rev. 1.3
Fulfills the OEM Requirements for Partial Networking Rev. 2.2
SOIC14 and DFN14 package with wettable flanks
Built-In Safety featuresTransmit data (TXD) dominant timeout function
RXD recessive clamping detection
Power-on Reset (POR)
Overtemperature protection
Undervoltage detection on VS, VCC and VIO pins
Transceiver disengages from the bus in over-temperature and low power supply mode
Bus Recessive/Dominant Clamping Detection

简介

ATA6570属于集成电路（IC）的驱动器接收器收发器。由制造生产的ATA6570驱动器，接收器，收发器该系列产品的主要功能是提供必需的硬件资源，以通过延长电缆或印制线进行通信。确切的功能会因所采用的通信协议而异，可能包括诸如瞬态抑制之类的功能，这些功能对于通信用途可能并非绝对必要，但对于可能的使用环境却是明智之选。