excom I/O System Input Module, Digital, 4-channel

The input module DI40-N is used for the connection of NAMUR sensors (DIN EN 60947-5-6), 3-wire sensors (NPN, PNP) or mechanical contacts. When wire-break or short-circuit monitoring are activated, mechanical contacts can only be connected with a corresponding resistor circuitry (WM1, Ident

文件：374.43 Kbytes 页数：3 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Output Module, Digital, 4-channel

The output module DO40-N is used for the connection of low-power actuators such as valves or indicator lights. The outputs of this module are galvanically isolated from each other. One actuator per channel can be connected. Via selection of connecting terminals, two circuits per channel are

文件：368.17 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Input Module, Analog, 4-channel

The input module AI40-N is used for the connection of 2-wire transducers (active input = source mode / transducer passive) or 4- wire transducers (passive input = sink mode / transducer active). The field circuits are galvanically isolated from each other. HART-compatible transducers can b

文件：530.28 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Input Module, Analog, Passive, 4-channel

The input module AI41-N is used for the connection of 4-wire transducers (passive input = sink mode / transducer active). The inputs are galvanically isolated from each The resolution is 14 bit, i.e. the analog value between 0…21 mA is represented as a number between 0 and 16383. For clear r

文件：367.4 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Potentiometer Module, 4-channel

The analog input module AI43-N is used for the connection of potentiometers in 3 or 4- wire technology. If 3-wire potentiometers are used, the terminals at the module rack have to be bridged. Resistance measurements, i.e. the evaluation of potentiometers with a 2-wire connection, is not poss

文件：370.58 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Output Module, Analog, 4-channel

The output module AO40-N is used for the connection of analog actuators such as control valves or process indicators. The outputs are galvanically isolated from each other. HART-compatible transducers can be connected to the module. The field device can thus be parametrized directly at the

文件：363.2 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Input Module, Analog, Active, HART, 4-channel

The input module AIH40-N is used for the connection of 2-wire transducers (active input = source mode / transducer passive). The inputs are not galvanically isolated from each other. When connecting the field devices, care has to be taken that all outputs are on the same potential. HART-comp

文件：573.94 Kbytes 页数：3 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Output Module, Analog, HART, 4-channel

The output module AOH40-N is used for the connection of analog actuators such as control valves or process indicators. The outputs are not galvanically isolated from each other. When connecting the field devices, care has to be taken that all outputs are on the same potential. HART-compatible

文件：547.74 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Input Module, Temperature, 4-channel

The input module TI40-N is used for the connection of 2, 3 and 4-wire temperature probes of the types Pt100, PT200, Pt500, Pt1000, Ni100 and CU100, as well as for the connection of thermocouples of the types B, E, D, J, K, L, N, R, S, T and U. The module can also be used for the measurement of

文件：375.59 Kbytes 页数：3 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司

excom I/O System Input Module, Temperature, 4-channel

The input module TI41-N is used for the connection of the 2, 3 and 4-wire temperature probes Pt100, Ni100, Cu50 and Cu100. Line compensation of 2-wire temperature resistors is done by means of parametrized resistance values. These values have to be determined first through measurements. The a

文件：353.52 Kbytes 页数：2 Pages

TURCKTurck, Inc.

图尔克德国图尔克集团公司