TWL6032数据手册集成电路（IC）的电源管理-专用规格书PDF

描述 Description

The TWL6032 device is an integrated power-management integrated circuit (PMIC) for applications powered by a rechargeable battery. The device provides five configurable step-down converters with a current capability of up to 5.0 A for memory, processor core, I/O, auxiliary, preregulation for LDOs, and so forth. The device also contains nine LDO regulators for external use that can be supplied from a battery or a preregulated supply. The power-up and power-down controller is configurable and can support any power-up or power-down sequence (programmed in OTP memory). The RTC provides three 32-kHz clock outputs: seconds, minutes, hours, day, month, and year information; as well as alarm wakeup and timer. The TWL6032 device supports 32-kHz clock generation based on a crystal oscillator.The device integrates a switched-mode system supply regulator from a USB connector. The switched-mode regulator includes power paths from the USB and battery with supplemental mode for immediate startup, even with an empty battery. The battery switch uses an external low-ohmic PMOS transistor allowing minimal serial resistance during fast charging and when operating from battery. The device can also be used without the external PMOS transistor; in this case, the battery is always tied to the system supply and the switched-mode regulator is used for battery charging. The TWL6032 device is available in a 155-pin WCSP package, 5.21 mm × 5.36 mm with a 0.4-mm ball pitch.

特性 Features

• Five Highly Efficient Buck Converters
• One 3 MHz, 0.6 to 2.1 V at 5.0 A, DVS-Capable
• One 6 MHz, 0.6 to 2.1 V at 2.5 A, DVS-Capable
• Three 6 MHz, 0.6 to 2.1 V at 1.1 A, One Is DVS-Capable
• Extended Mode for Higher Output Voltages

• 11 General-Purpose Low-Dropout Voltage Regulators (LDOs)
• Six 1.0 to 3.3 V at 0.2 A With Battery or Preregulated Supply:
• One Can be Used as Vibrator Driver
• One 1.0 to 3.3 V at 50 mA With Battery or Preregulated Supply
• One Low-Noise 1.0 to 3.3 V at 50 mA With Battery or Preregulated Supply
• One 3.3 V at 100 mA USB LDO
• Two LDOs for TWL6032 Internal Use


• USB OTG Module:
• ID Detection, Accessory Charger Adapter (ACA) Support
• Accessory Detection Protocol (ADP) Support

• Backup Battery Charger
• 12-Bit Sigma-Delta Analog-to-Digital Converter (ADC) With 19 Input Channels:
• Seven External Input Channels

• 13-Bit Coulomb Counter With Four Programmable Integration Periods
• Low-Power Consumption:
• 8 µA in BACKUP State
• 20 µA in WAIT-ON State
• 110 µA in SLEEP State, With Two DC-DC Converters Active

• Real-Time Clock (RTC) With Timer and Alarm Wake-Up:
• Three Buffered 32-kHz Outputs

• SIM and SD/MMC Card Detections
• Two Digital PWM Outputs
• Thermal Monitoring:
• High-Temperature Warning
• Thermal Shutdown

• Control:
• Configurable Power-Up and Power-Down Sequences (OTP Memory)
• Configurable Sequences Between SLEEP and ACTIVE States (OTP Memory)
• Three Digital Output Signals that can be Included in the Startup Sequence to Control External Devices
• Two Inter-Integrated Circuit (I2C) Interfaces
• All Resources Configurable by I2C

• System Voltage Regulator and Battery Charger With Power Path From USB:
• Input Current Limit to Comply With USB Standard
• 3-MHz Switched-Mode Regulator With Integrated Power FET for up to 2.0-A Current
• Dedicated Control Loop for Battery Current and Voltage
• External Low-Ohmic FET for Power Path and Battery Charging
• Boost Mode Operation for USB OTG
• Supplement Mode to Deliver Current From Battery During Power Path Operation
• Charger for Single-Cell Li-Ion and Li-Polymer Battery Packs
• Safety Timer and Reset Control
• Thermal Protection
• Input/Output Overvoltage Protection
• Charging Indicator LED Driver
• Compliant With:
• USB 2.0
• OTG and EH 2.0
• USB Battery Charging 1.2
• YD/T 1591-2006
• Japanese Battery Charging Guidelines (JEITA)


• Battery Voltage Range From 2.5 to 5.5 V
• Package 5.21-mm × 5.36-mm 155-Pin WCSP