TVS0701 7-V Bidirectional Flat-Clamp Surge Protection Device

1 Features 1• Protection Against 1-kV, 42-Ω IEC 61000-4-5 Surge Test for Industrial Signal Lines • Bidirectional Polarity Enables Protection Against Bipolar Signaling or Miswiring Conditions • Clamping Voltage of 11 V at 30-A, 8/20-μs Surge Current • Standoff Voltage: ±7 V • Small 3-mm × 3

文件：712.25 Kbytes 页数：21 Pages

TI

德州仪器

TVS2201 22-V Bidirectional Flat-Clamp Surge Protection Device

1 Features 1• Protection Against 1-kV, 42-Ω IEC 61000-4-5 Surge Test for Industrial Signal Lines • Bidirectional Polarity Enables Protection Against Bipolar Signaling or Miswiring Conditions • Clamping Voltage of 29.6 V at 30 A of 8/20-μs Surge Current • Standoff Voltage: ±22 V • Small 3 m

文件：726.41 Kbytes 页数：21 Pages

TI

德州仪器

TVS2701 27-V Bidirectional Flat-Clamp Surge Protection Device

1 Features 1• Protection Against 1-kV, 42-Ω IEC 61000-4-5 Surge Test for Industrial Signal Lines • Bidirectional Polarity Enables Protection Against Bipolar Signaling or Miswiring Conditions • Clamping Voltage of 34 V at 27-A, 8/20-μs Surge Current • Standoff Voltage: ±27 V • Small 3 mm ×

文件：752.73 Kbytes 页数：21 Pages

TI

德州仪器

7-V Bidirectional Flat-Clamp Surge Protection Device

文件：366.52 Kbytes 页数：15 Pages

TI

德州仪器

7V 双向平缓钳位浪涌保护器件

TVS0701 器件可将高达 30A 的 IEC 61000-4-5 故障电流进行分流，以保护系统免受高功率瞬态冲击或雷击。该器件可通过 42Ω 阻抗进行耦合的方式承受 1kV 的 IEC 61000-4-5 开路电压，满足常见的工业信号线路 EMC 要求。TVS0701 使用反馈机制确保在故障期间发挥精确的平缓钳位能力，使系统接触电压始终低于传统 TVS 二极管。精确的电压调节允许设计人员放心地选择具有较低电压容差的系统组件，从而能够在不影响可靠性的情况下降低系统成本和复杂度。TVS0701 具有 ±7V 的工作范围，可在需要反向接线情形防护的系统中运行。\n\n此外，TVS0701 还采用 • 保护特性符合针对工业信号线路的 1kV、42Ω IEC 61000-4-5 浪涌测试要求\n• 双向极性可针对双极信号传输或误接线情形提供保护\n• 30A、8/20µs 浪涌电流下的钳位电压为 11V \n• 关断电压：±7V\n• 3mm × 3mm 小型 SON 封装\n• 在 125°C 时，可耐受超过 5,000 次的 30A 8/20µs 浪涌电流的重复冲击\n• 强大的浪涌保护 \n• IEC 61000-4-5 (8/20µs)：30A \n• IEC61643-321 (10/1000 µs)：15A \n \n• 低泄漏电流 \n• 27°C 时的典型值为 0.25nA;

TI

德州仪器

丝印：1QCP；Package：SON；TVS0701 7-V Bidirectional Flat-Clamp Surge Protection Device

1 Features 1• Protection Against 1-kV, 42-Ω IEC 61000-4-5 Surge Test for Industrial Signal Lines • Bidirectional Polarity Enables Protection Against Bipolar Signaling or Miswiring Conditions • Clamping Voltage of 11 V at 30-A, 8/20-μs Surge Current • Standoff Voltage: ±7 V • Small 3-mm × 3

文件：712.25 Kbytes 页数：21 Pages

TI

德州仪器

丝印：1QCP；Package：SON；TVS0701 7-V Bidirectional Flat-Clamp Surge Protection Device

1 Features 1• Protection Against 1-kV, 42-Ω IEC 61000-4-5 Surge Test for Industrial Signal Lines • Bidirectional Polarity Enables Protection Against Bipolar Signaling or Miswiring Conditions • Clamping Voltage of 11 V at 30-A, 8/20-μs Surge Current • Standoff Voltage: ±7 V • Small 3-mm × 3

文件：712.25 Kbytes 页数：21 Pages

TI

德州仪器

7-V Bidirectional Flat-Clamp Surge Protection Device

文件：366.52 Kbytes 页数：15 Pages

TI

德州仪器

Package：8-VDFN 裸露焊盘；包装：散装 类别：电路保护 TVS - 混合技术 描述：TVS ARRAYS

TI

德州仪器