TLE9263QXV33数据手册集成电路（IC）的专用规格书PDF

描述 Description

The TLE9263QXV33 is a monolithic integrated circuit in an exposed pad VQFN-48 (7mm x 7mm) power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI). The device is designed for various CAN-LIN automotive applications as main supply for the microcontroller and as interface for a LIN and CAN bus network.
To support these applications, the System Basis Chip (SBC) provides the main functions, such as a 3.3V lowdropout voltage regulator (LDO) for e.g. a microcontroller supply, another 5V low-dropout voltage regulator with off-board protection for e.g. sensor supply, another 3.3V/1.8V regulator to drive an external PNP transistor, which can be used as an independent supply for off-board usage or in load sharing configuration with the main regulator VCC1, a HS-CAN transceiver supporting CAN FD and LIN transceiver for data transmission, high-side switches with embedded protective functions and a 16-bit Serial Peripheral Interface (SPI) to control and monitor the device. Also implemented are a configurable timeout / window watchdog circuit with a reset feature, three Fail Outputs and an under voltage reset feature.
The device offers low-power modes in order to minimize current consumption on applications that are connected permanently to the battery. A wake-up from the low-power mode is possible via a message on the buses, via the bi-level sensitive monitoring/wake-up inputs as well as via cyclic wake.
The device is designed to withstand the severe conditions of automotive applications.

特性 Features

·Very low quiescent current consumption in Stop- and Sleep Mode
·Periodic Cyclic Wake in SBC Normal- and Stop Mode
·Periodic Cyclic Sense in SBC Normal-, Stop- and Sleep Mode
·Low-Drop Voltage Regulator 3.3V, 250mA
·Low-Drop Voltage Regulator 5V, 100mA, protected features for off-board usage
·Low-Drop Voltage Regulator, driving an external PNP transistor - 3.3V in load sharing configuration or 3.3V/1.8V in stand-alone configuration, protected features for off-board usage. Current limitation by shunt resistor (up to 350mA with 470mΩ external shunt resistor) in stand-alone configuration
·High-Speed CAN Transceiver
·Two LIN Transceivers LIN 2.2, J2602 with configurable TXD timeout feature and LIN Flash Mode
·Fully compliant to “Hardware Requirements for LIN, CAN and FlexRay Interfaces in Automotive Applications”
·Four High-Side Outputs 7Ω typ.
·Two General Purpose High-Voltage In- and Outputs (GPIOs) configurable as add. Fail Outputs, Wake Inputs, Low-Side switches or High-Side switches
·Three universal High-Voltage Wake Inputs for voltage level monitoring
·Alternate High-Voltage Measurement Function, e.g. for battery voltage sensing
·Configurable wake-up sources
·Reset Output
·Configurable timeout and window watchdog
·Up to three Fail Outputs (depending on configuration)
·Over temperature and short circuit protection feature
·Wide supply input voltage and temperature range
·Software compatible to all SBC families TLE926x and TLE927x
·Green Product (RoHS compliant) & AEC Qualified
·PG-VQFN-48 leadless exposed-pad power package with Lead Tip Inspection (LTI) feature to support Automatic Optical Inspection (AOI)

简介

TLE9263QXV33属于集成电路（IC）的专用。由制造生产的TLE9263QXV33专用该系列产品可提供所需的功能，用以将信息源/信宿连到各种复杂或范围狭窄应用中的传感器、变送器、致动器、传输介质或其他此类端点。例如，汽车安全气囊驱动器、车身控制和信息娱乐总线、自适应电缆均衡器、智能卡等等。