STM8L101

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C

STM8L101F2

超低功耗8位MCU，具有4 KB Flash、16 MHz CPU和集成EEPROM; • Main microcontroller features \n •Supply voltage range 1.65 V to 3.6 V \n •Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz) \n •STM8 Core with up to 16 CISC MIPS throughput \n •Temp. range: -40 to 85 °C and 125 °C \n• Memories \n •Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM \n •Error correction code (ECC) \n •Flexible write and read protection modes \n •In-application and in-circuit programming \n •Data EEPROM capability \n •1.5 Kbytes of static RAM \n• Clock management \n •Internal 16 MHz RC with fast wakeup time (typ. 4 µs) \n •Internal low consumption 38 kHz RC driving both the IWDG and the AWU \n• Reset and supply management \n •Ultra-low power POR/PDR \n •Three low-power modes: Wait, Active-halt, Halt \n• Interrupt management \n •Nested interrupt controller with software priority control \n •Up to 29 external interrupt sources \n• I/Os \n •Up to 30 I/Os, all mappable on external interrupt vectors \n •I/Os with programmable input pull-ups, high sink/source capability and one LED driver infrared output \n• Peripherals \n •Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM) \n •One 8-bit timer (TIM4) with 7-bit prescaler \n •Infrared remote control (IR) \n •Independent watchdog \n •Auto-wakeup unit \n •Beeper timer with 1, 2 or 4 kHz frequencies \n •SPI synchronous serial interface \n •Fast I2C Multimaster/slave 400 kHz \n •USART with fractional baud rate generator \n •2 comparators with 4 inputs each \n• Development support \n •Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging \n •In-circuit emulation (ICE) \n• 96-bit unique ID;

The STM8L101x1 STM8L101x2 STM8L101x3 low-power family features the enhanced STM8 CPU core providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the advantages of a CISC architecture with improved code density, a 24-bit linear addressing space and an optimized architecture for low power operations.\n\n The family includes an integrated debug module with a hardware interface (SWIM) which allows non-intrusive in-application debugging and ultrafast Flash programming.\n\n All STM8L101xx microcontrollers feature low power low-voltage single-supply program Flash memory. The 8-Kbyte devices embed data EEPROM.\n\n The STM8L101xx low power family is based on a generic set of state-of-the-art peripherals. The modular design of the peripheral set allows the same peripherals to be found in different ST microcontroller families including 32-bit families. This makes any transition to a different family very easy, and simplified even more by the use of a common set of development tools.\n\n All STM8L low power products are based on the same architecture with the same memory mapping and a coherent pinout.\n\n

STM8L101F3

超低功耗8位MCU，具有8 KB Flash、16 MHz CPU和最大2-KB的EEPROM; • Main microcontroller features \n •Supply voltage range 1.65 V to 3.6 V \n •Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz) \n •STM8 Core with up to 16 CISC MIPS throughput \n •Temp. range: -40 to 85 °C and 125 °C \n• Memories \n •Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM \n •Error correction code (ECC) \n •Flexible write and read protection modes \n •In-application and in-circuit programming \n •Data EEPROM capability \n •1.5 Kbytes of static RAM \n• Clock management \n •Internal 16 MHz RC with fast wakeup time (typ. 4 µs) \n •Internal low consumption 38 kHz RC driving both the IWDG and the AWU \n• Reset and supply management \n •Ultra-low power POR/PDR \n •Three low-power modes: Wait, Active-halt, Halt \n• Interrupt management \n •Nested interrupt controller with software priority control \n •Up to 29 external interrupt sources \n• I/Os \n •Up to 30 I/Os, all mappable on external interrupt vectors \n •I/Os with programmable input pull-ups, high sink/source capability and one LED driver infrared output \n• Peripherals \n •Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM) \n •One 8-bit timer (TIM4) with 7-bit prescaler \n •Infrared remote control (IR) \n •Independent watchdog \n •Auto-wakeup unit \n •Beeper timer with 1, 2 or 4 kHz frequencies \n •SPI synchronous serial interface \n •Fast I2C Multimaster/slave 400 kHz \n •USART with fractional baud rate generator \n •2 comparators with 4 inputs each \n• Development support \n •Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging \n •In-circuit emulation (ICE) \n• 96-bit unique ID;

The STM8L101x1 STM8L101x2 STM8L101x3 low-power family features the enhanced STM8 CPU core providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the advantages of a CISC architecture with improved code density, a 24-bit linear addressing space and an optimized architecture for low power operations.\n\n The family includes an integrated debug module with a hardware interface (SWIM) which allows non-intrusive in-application debugging and ultrafast Flash programming.\n\n All STM8L101xx microcontrollers feature low power low-voltage single-supply program Flash memory. The 8-Kbyte devices embed data EEPROM.\n\n The STM8L101xx low power family is based on a generic set of state-of-the-art peripherals. The modular design of the peripheral set allows the same peripherals to be found in different ST microcontroller families including 32-bit families. This makes any transition to a different family very easy, and simplified even more by the use of a common set of development tools.\n\n All STM8L low power products are based on the same architecture with the same memory mapping and a coherent pinout.\n\n

STM8L101G2

超低功耗8位MCU，具有4 KB Flash、16 MHz CPU和集成EEPROM; • Main microcontroller features \n •Supply voltage range 1.65 V to 3.6 V \n •Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz) \n •STM8 Core with up to 16 CISC MIPS throughput \n •Temp. range: -40 to 85 °C and 125 °C \n• Memories \n •Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM \n •Error correction code (ECC) \n •Flexible write and read protection modes \n •In-application and in-circuit programming \n •Data EEPROM capability \n •1.5 Kbytes of static RAM \n• Clock management \n •Internal 16 MHz RC with fast wakeup time (typ. 4 µs) \n •Internal low consumption 38 kHz RC driving both the IWDG and the AWU \n• Reset and supply management \n •Ultra-low power POR/PDR \n •Three low-power modes: Wait, Active-halt, Halt \n• Interrupt management \n •Nested interrupt controller with software priority control \n •Up to 29 external interrupt sources \n• I/Os \n •Up to 30 I/Os, all mappable on external interrupt vectors \n •I/Os with programmable input pull-ups, high sink/source capability and one LED driver infrared output \n• Peripherals \n •Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM) \n •One 8-bit timer (TIM4) with 7-bit prescaler \n •Infrared remote control (IR) \n •Independent watchdog \n •Auto-wakeup unit \n •Beeper timer with 1, 2 or 4 kHz frequencies \n •SPI synchronous serial interface \n •Fast I2C Multimaster/slave 400 kHz \n •USART with fractional baud rate generator \n •2 comparators with 4 inputs each \n• Development support \n •Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging \n •In-circuit emulation (ICE) \n• 96-bit unique ID;

The STM8L101x1 STM8L101x2 STM8L101x3 low-power family features the enhanced STM8 CPU core providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the advantages of a CISC architecture with improved code density, a 24-bit linear addressing space and an optimized architecture for low power operations.\n\n The family includes an integrated debug module with a hardware interface (SWIM) which allows non-intrusive in-application debugging and ultrafast Flash programming.\n\n All STM8L101xx microcontrollers feature low power low-voltage single-supply program Flash memory. The 8-Kbyte devices embed data EEPROM.\n\n The STM8L101xx low power family is based on a generic set of state-of-the-art peripherals. The modular design of the peripheral set allows the same peripherals to be found in different ST microcontroller families including 32-bit families. This makes any transition to a different family very easy, and simplified even more by the use of a common set of development tools.\n\n All STM8L low power products are based on the same architecture with the same memory mapping and a coherent pinout.\n\n

STM8L101-EVAL

STM8L101-EVAL evaluation board

STM8L101F1P3

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C

STM8L101F1P3A

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C

STM8L101F1P3ATR

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C

STM8L101F1P3TR

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C

STM8L101F1P6

8-bit ultralow power microcontroller with up to 8 Kbytes Flash multifunction timers, comparators, USART, SPI, I2C