SN74AVCH4T245中文资料具有可配置电压转换和三态输出的 4 位双电源总线收发器数据手册TI规格书

描述 Description

This 4-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. The SN74AVCH4T245 is optimized to operate with VCCA/VCCB set at 1.4 V to 3.6 V. It is operational with VCCA/VCCB as low as 1.2 V. This allows for universal low voltage bidirectional translation between any of the 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V voltage nodes.

The SN74AVCH4T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.

The SN74AVCH4T245 device control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCA.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature ensures that if either VCC input is at GND, then both ports are in the high-impedance state. The bus-hold circuitry on the powered-up side always stays active.

Active bus-hold circuitry holds unused or undriven data inputs at a valid logic state. Use of pull-up or pull-down resistors with the bus-hold circuitry is not recommended. The bus-hold circuitry on the powered-up side always stays active.

To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pull-up resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

特性 Features

• Control Inputs VIH/VIL Levels are Referenced to VCCA Voltage
• Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.2V to 3.6V Power- Supply Range
• I/Os Are 4.6V Tolerant
• Ioff Supports Partial Power-Down-Mode Operation
• Bus Hold on Data Inputs Eliminates the Need for External pull-up/pull-down Resistors
• Max Data Rates
• 380 Mbps (1.8 V to 3.3 V Translation)
• 200 Mbps (
• Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
• ESD Protection Exceeds JESD 22
• 8000 V Human Body Model (A114-A)
• 200 V Machine Model (A115-A)
• 1000 V Charged-Device Model (C101)

简介

SN74AVCH4T245属于集成电路（IC）的缓冲器驱动器接收器收发器。由TI制造生产的SN74AVCH4T245缓冲器，驱动器，接收器，收发器逻辑缓冲器、驱动器、接收器和收发器允许隔离对某个电路的逻辑信号的访问，以用于另一电路。缓冲器将其输入信号（不变或反相）传递到其输出，并可能用于清除弱信号或驱动负载。在布尔逻辑仿真器中，缓冲器主要用于增加传播延迟。逻辑接收器和收发器允许在数据总线之间进行隔离通信。