SPI to IC-bus interface

General description The SC18IS600/601 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600/601 can operate as an I2C-

文件：153.87 Kbytes 页数：28 Pages

PHI

飞利浦

SPI to I2C-bus interface

General description The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus mast

文件：173.9 Kbytes 页数：30 Pages

恩XP

I2C-bus to SPI bridge

General description\nThe SC18IS600/601 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600/601 can operate as an I2C-bu ■ SPI slave interface\n■ SPI Mode 3\n■ Master I2C-bus controller\n■ General Purpose Input/Output (GPIO) pins: 4 (SC18IS600); 3 (SC18IS601)\n■ Two quasi-bidirectional I/O pins\n■ 5 V tolerant I/O pins\n■ High-speed SPI:\n   ♦ Up to 3 Mbit/s (SC18IS601)\n   ♦ Up to 1.2 Mbit/s (SC18IS600)\n■ High-speed;

恩XP

SPI to I2C-bus interface

General description The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus mast

文件：173.9 Kbytes 页数：30 Pages

恩XP

SPI to IC-bus interface

General description The SC18IS600/601 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600/601 can operate as an I2C-

文件：153.87 Kbytes 页数：28 Pages

PHI

飞利浦

SPI至I²C总线接口

SC18IS600可用作主机（微控制器、微处理器、芯片组等）标准SPI和串行I²C总线之间的接口。允许主机与其他I²C总线器件直接通信。SC18IS600用作I²C总线主发送器或主接收器。SC18IS600控制所有I²C总线特定序列、协议、仲裁和定时。 SPI从属接口\nSPI模式3\n单主I²C总线控制器\n四个通用输入/输出(GPIO)引脚\n两个准双向I/O引脚\n5 V容限的I/O引脚\n高速SPI：最快为1.2 Mbit/s\n高速I²C总线：400 kbit/s\n96字节发送缓冲器\n96字节接收缓冲器\n2.4 V至3.6 V操作\n带有WAKEUP引脚的节电模式\n内部振荡器\n有源LOW中断输出\n提供极小型TSSOP16和HVQFN24封装;

恩XP