SPI to IC-bus interface

General description The SC18IS600/601 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600/601 can operate as an I2C-

文件：153.87 Kbytes 页数：28 Pages

PHI

飞利浦

SPI to I2C-bus interface

General description The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus mast

文件：173.9 Kbytes 页数：30 Pages

恩XP

Smart, simple solutions for the 12 most common design concerns

文件：727.81 Kbytes 页数：8 Pages

恩XP

SPI to I2C-bus interface

General description The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus mast

文件：173.9 Kbytes 页数：30 Pages

恩XP

SPI to I2C-bus interface

General description The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus mast

文件：173.9 Kbytes 页数：30 Pages

恩XP

SPI to IC-bus interface

General description The SC18IS600/601 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600/601 can operate as an I2C-

文件：153.87 Kbytes 页数：28 Pages

PHI

飞利浦

SPI至I²C总线接口

SC18IS600可用作主机（微控制器、微处理器、芯片组等）标准SPI和串行I²C总线之间的接口。允许主机与其他I²C总线器件直接通信。SC18IS600用作I²C总线主发送器或主接收器。SC18IS600控制所有I²C总线特定序列、协议、仲裁和定时。 SPI从属接口\n SPI模式3\n 单主I²C总线控制器\n 四个通用输入/输出(GPIO)引脚\n 两个准双向I/O引脚\n 5 V容限的I/O引脚\n 高速SPI：最快为1.2 Mbit/s\n 高速I²C总线：400 kbit/s\n 96字节发送缓冲器\n 96字节接收缓冲器\n 2.4 V至3.6 V操作\n 带有WAKEUP引脚的节电模式\n 内部振荡器\n 有源LOW中断输出\n 提供极小型TSSOP16和HVQFN24封装;

恩XP

恩智浦

SPI to I2C-bus interface

The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus master-transmitter or maste • SPI slave interface\n• SPI Mode 3\n• Single master I2C-bus controller\n• Four General Purpose Input/Output (GPIO) pins\n• Two quasi-bidirectional I/O pins\n• 5 V tolerant I/O pins\n• High-speed SPI: Up to 1.2 Mbit/s\n• High-speed I2C-bus: 400 kbit/s\n• 96-byte transmit buffer\n• 96-byte receive bu;

恩XP

恩智浦

SPI to I2C-bus interface

The SC18IS600 is designed to serve as an interface between the standard SPI of a host (microcontroller, microprocessor, chip set, etc.) and the serial I2C-bus. This allows the host to communicate directly with other I2C-bus devices. The SC18IS600 can operate as an I2C-bus master-transmitter or maste • SPI slave interface\n• SPI Mode 3\n• Single master I2C-bus controller\n• Four General Purpose Input/Output (GPIO) pins\n• Two quasi-bidirectional I/O pins\n• 5 V tolerant I/O pins\n• High-speed SPI: Up to 1.2 Mbit/s\n• High-speed I2C-bus: 400 kbit/s\n• 96-byte transmit buffer\n• 96-byte receive bu;

恩XP

恩智浦