PCA9539RBS

16-bit I2C-bus and SMBus low power I/O port with interrupt and reset; • 16-bit I2C-bus GPIO with interrupt and reset\n• Operating power supply voltage range of 2.3 V to 5.5 V (3.0 V to 5.5 V for PCA9539PW/Q900 andPCA9539RPW/Q900)\n• 5 V tolerant I/Os\n• Polarity inversion register\n• Active LOW interrupt output\n• Active LOW reset input\n• Low standby current\n• Noise filter on SCL/SDA inputs\n• No glitch on power-up\n• Internal power-on reset\n• 16 I/O pins which default to 16 inputs\n• 0 Hz to 400 kHz clock frequency\n• ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM perJESD22-C101\n• Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\n• Offered in three different packages: SO24, TSSOP24, and HVQFN24\n;

The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of General Purpose parallel Input/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.\nThe PCA9539; PCA9539R consists of two 8-bit configuration (input or output selection), input, output and polarity inversion (active HIGH or active LOW operation) registers. The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the read register can be inverted with the Polarity inversion register. All registers can be read by the system master.\nThe PCA9539; PCA9539R is identical to the PCA9555 except for the removal of the internal I/O pull-up resistor which greatly reduces power consumption when the I/Os are held LOW, replacement of A2 with RESET and a different address range.\nThe PCA9539; PCA9539R open-drain interrupt output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed.\nThe power-on reset sets the registers to their default values and initializes the device state machine. In the PCA9539, the RESET pin causes the same reset/default I/O input configuration to occur without de-powering the device, holding the registers and I2C-bus state machine in their default state until the RESET input is once again HIGH. This input requires a pull-up to VDD. In the PCA9539R however, only the device state machine is initialized by the RESET pin and the internal general-purpose registers remain unchanged. Using the PCA9539R RESET pin will only reset the I2C-bus interface should it be stuck LOW to regain access to the I2C-bus. This allows the I/O pins to retain their last configured state so that they can keep any lines in their previously defined state and not cause system errors while the I2C-bus is being restored.\nTwo hardware pins (A0, A1) vary the fixed I2C-bus address and allow up to four devices to share the same I2C-bus/SMBus.\n

PCA9539RPW

16-bit I2C-bus and SMBus low power I/O port with interrupt and reset; • 16-bit I2C-bus GPIO with interrupt and reset\n• Operating power supply voltage range of 2.3 V to 5.5 V (3.0 V to 5.5 V for PCA9539PW/Q900 andPCA9539RPW/Q900)\n• 5 V tolerant I/Os\n• Polarity inversion register\n• Active LOW interrupt output\n• Active LOW reset input\n• Low standby current\n• Noise filter on SCL/SDA inputs\n• No glitch on power-up\n• Internal power-on reset\n• 16 I/O pins which default to 16 inputs\n• 0 Hz to 400 kHz clock frequency\n• ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM perJESD22-C101\n• Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\n• Offered in three different packages: SO24, TSSOP24, and HVQFN24\n;

The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of General Purpose parallel Input/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.\nThe PCA9539; PCA9539R consists of two 8-bit configuration (input or output selection), input, output and polarity inversion (active HIGH or active LOW operation) registers. The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the read register can be inverted with the Polarity inversion register. All registers can be read by the system master.\nThe PCA9539; PCA9539R is identical to the PCA9555 except for the removal of the internal I/O pull-up resistor which greatly reduces power consumption when the I/Os are held LOW, replacement of A2 with RESET and a different address range.\nThe PCA9539; PCA9539R open-drain interrupt output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed.\nThe power-on reset sets the registers to their default values and initializes the device state machine. In the PCA9539, the RESET pin causes the same reset/default I/O input configuration to occur without de-powering the device, holding the registers and I2C-bus state machine in their default state until the RESET input is once again HIGH. This input requires a pull-up to VDD. In the PCA9539R however, only the device state machine is initialized by the RESET pin and the internal general-purpose registers remain unchanged. Using the PCA9539R RESET pin will only reset the I2C-bus interface should it be stuck LOW to regain access to the I2C-bus. This allows the I/O pins to retain their last configured state so that they can keep any lines in their previously defined state and not cause system errors while the I2C-bus is being restored.\nTwo hardware pins (A0, A1) vary the fixed I2C-bus address and allow up to four devices to share the same I2C-bus/SMBus.\n

PCA9539RGER

REMOTE 16-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS

PCA9539RGER

SMBus Low-Power I/O Expander

PCA9539RHLR

REMOTE 16-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS

PCA9539RGER

Package：24-VFQFN 裸露焊盘；包装：卷带（TR）剪切带（CT）Digi-Reel® 得捷定制卷带 类别：集成电路（IC） I/O 扩展器 描述：IC I/O EXPANDER I2C 16B 24VQFN