首页>M58BW016FT80ZA3FT>规格书详情
M58BW016FT80ZA3FT中文资料意法半导体数据手册PDF规格书
相关芯片规格书
更多- M58BW016FT80T3FT
- M58BW016FB80T3FF
- M58BW016FT70ZA3FF
- M58BW016FB80ZA3FT
- M58BW016FT70T3FT
- M58BW016FB80T3FT
- M58BW016FB80ZA3FF
- M58BW016FT
- M58BW016FT70ZA3FT
- M58BW016FT70T3FF
- M58BW016FT80ZA3FF
- M58BW016FT7T3FT
- M58BW016FB8T3FT
- M58BW016FB8ZA3FT
- M58BW016FT7ZA3FF
- M58BW016FB8ZA3FF
- M58BW016FB8T3FF
- M58BW016FT7T3FF
M58BW016FT80ZA3FT规格书详情
Description
The M58BW016DT, M58BW016DB, M58BW016FT and M58BW016FB are 16 Mbit nonvolatile Flash memories that can be erased electrically at the block level and programmed in-system on a double-word basis using a 2.7 V to 3.6 V VDD supply for the circuit and a VDDQ supply down to 2.4 V for the input and output buffers. Optionally a 12 V VPP supply can be used to provide fast program and erase for a limited time and number of program/erase cycles.
The devices support Asynchronous (Latch Controlled and Page Read) and Synchronous Bus operations. The Synchronous Burst Read interface allows a high data transfer rate controlled by the Burst Clock, K, signal. It is capable of bursting fixed or unlimited lengths of data. The burst type, latency and length can be configured and can be easily adapted to a large variety of system clock frequencies and microprocessors. All writes are asynchronous. On power-up the memory defaults to Read mode with an Asynchronous Bus.
The devices have a boot block architecture with an array of 8 parameter blocks of 64 Kb each and 31 main blocks of 512 Kb each. In the M58BW016DT and M58BW016FT the parameter blocks are located at the top of the address space whereas in the M58BW016DB and M58BW016FB, they are located at the bottom.
Program and Erase commands are written to the command interface of the memory. An on chip Program/Erase controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a program or erase operation can be detected and any error conditions identified in the Status Register. The command set required to control the memory is consistent with JEDEC standards.
Features
■ Supply voltage
– VDD = 2.7 V to 3.6 V for Program, Erase and Read
– VDDQ = VDDQIN = 2.4 V to 3.6 V for I/O buffers
– VPP = 12 V for Fast Program (optional)
■ High performance
– Access times: 70, 80 ns
– 56 MHz effective zero wait-state Burst Read
– Synchronous Burst Read
– Asynchronous Page Read
■ Hardware block protection
– WP pin for Write Protect of the 4 outermost
parameter blocks and all main blocks
– RP pin for Write Protect of all blocks
■ Optimized for FDI drivers
– Fast Program / Erase Suspend latency time < 6 µs
– Common Flash interface
■ Memory blocks
– 8 parameters blocks (top or bottom)
– 31 main blocks
■ Low power consumption
– 5 µA typical Deep Power-down
– 60 µA typical standby for M58BW016DT/B
150 µA typical standby for M58BW016FT/B
– Automatic standby after Asynchronous Read
■ Electronic signature
– Manufacturer code: 20h
– Top device code: 8836h
– Bottom device code: 8835h
■ ECOPACK® packages available
产品属性
- 型号:
M58BW016FT80ZA3FT
- 制造商:
STMICROELECTRONICS
- 制造商全称:
STMicroelectronics
- 功能描述:
16 Mbit(512 Kb x 32, boot block, burst) 3 V supply Flash memories
供应商 | 型号 | 品牌 | 批号 | 封装 | 库存 | 备注 | 价格 |
---|---|---|---|---|---|---|---|
ST |
2020+ |
PQFP80 |
80000 |
只做自己库存,全新原装进口正品假一赔百,可开13%增 |
询价 | ||
MICRON |
1844+ |
PQFP |
6528 |
只做原装正品假一赔十为客户做到零风险!! |
询价 | ||
ST |
QFP80 |
93480 |
集团化配单-有更多数量-免费送样-原包装正品现货-正规 |
询价 | |||
Numonyx-ADIVISIONOFMICRO |
2022 |
ICFLASH16MBIT45NS80PQFP |
5058 |
原厂原装正品,价格超越代理 |
询价 | ||
Micron Technology Inc |
23+/24+ |
80-BQFP |
8600 |
只供原装进口公司现货+可订货 |
询价 | ||
NA |
22+ |
594 |
原装现货假一赔十 |
询价 | |||
MICRON/美光 |
2021+ |
PQFP-80 |
100500 |
一级代理专营品牌!原装正品,优势现货,长期排单到货 |
询价 | ||
Micron Technology Inc. |
24+ |
80-BQFP |
9350 |
独立分销商,公司只做原装,诚心经营,免费试样正品保证 |
询价 | ||
Numonyx/STMi |
23+ |
80-PQFP |
65480 |
询价 | |||
ST |
22+ |
BGA |
32350 |
原装正品 假一罚十 公司现货 |
询价 |