CC1100

专为低功耗无线应用设计的高度集成的多通道射频收发器; RF Performance\r\nHigh sensitivity (–111 dBm at 1.2 kBaud, 868 MHz, 1% packet error rate)\r\nLow current consumption (14.4 mA in RX, 1.2 kBaud, 868 MHz)\r\nProgrammable output power up to +10 dBm for all supported frequencies\r\nExcellent receiver selectivity and blocking performance\r\nProgrammable data rate from 1.2 to 500 kBaud\r\nFrequency bands: 300-348 MHz, 400-464 MHz and 800-928 MHz\r\nAnalog Features\r\n2-FSK, GFSK, and MSK supported as well as OOK and flexible ASK shaping\r\nSuitable for frequency hopping systems due to a fast settling frequency synthesizer: 90µs settling time\r\nAutomatic Frequency Compensation (AFC) can be used to align the frequency synthesizer to the received centre frequency\r\nIntegrated analog temperature sensor\r\nDigital Features\r\nFlexible support for packet oriented systems: On-chip support for sync word detection, address check, flexible packet length, and automatic CRC handling\r\nEfficient SPI interface: All registers can be programmed with one \"burst\" transfer\r\nDigital RSSI output\r\nProgrammable channel filter bandwidth\r\nProgrammable Carrier Sense (CS) indicator\r\nProgrammable Preamble Quality Indicator (PQI) for improved protection against false sync word detection in random noise\r\nSupport for automatic Clear Channel Assessment (CCA) before transmitting (for listen-before-talk systems)\r\nSupport for per-package Link Quality Indication (LQI)\r\nOptional automatic whitening and dewhitening of data\r\nLow-Power Features\r\n400nA SLEEP mode current consumption\r\nFast startup time: 240µs from sleep to RX or TX mode (measured on EM reference design [5] and [6])\r\nWake-on-radio functionality for automatic low-power RX polling\r\nSeparate 64-byte RX and TX data FIFOs (enables burst mode data transmission)\r\nGeneral\r\nFew external components: Completely onchip frequency synthesizer, no external filters or RF switch needed\r\nGreen package: RoHS compliant and no antimony or bromine\r\nSmall size (QLP 4×4 mm package, 20 pins)\r\nSuited for systems targeting compliance with EN 300 220 (Europe) and FCC CFR Part 15 (US).\r\nSupport for asynchronous and synchronous serial receive/transmit mode for backwards compatibility with existing radio communication protocols\r\nApplications\r\nUltra low-power wireless applications operating in the 315/433/868/915 MHz ISM/SRD bands\r\nWireless alarm and security systems\r\nIndustrial monitoring and control\r\nWireless sensor networks\r\nAMR – Automatic Meter Reading\r\nHome and building automation;

The CC1100 is a low-cost sub- 1 GHz transceiver designed for very low-power wireless applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency bands at 315, 433, 868, and 915 MHz, but can easily be programmed for operation at other frequencies in the 300-348 MHz, 400-464 MHz and 800-928 MHz bands.\r\n\r\nThe RF transceiver is integrated with a highly configurable baseband modem. The modem supports various modulation formats and has a configurable data up to 500 kBaud.\r\n\r\nCC1100 provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio.\r\n\r\nThe main operating parameters and the 64-byte transmit/receive FIFOs of CC1100 can be controlled via an SPI interface. In a typical system, the CC1100 will be used together with a microcontroller and a few additional passive components.

CC1100

CC1100 Single Chip Low Cost Low Power RF-Transceiver

CC1100

SWRU197H?밪eptember 2010?밨evised April 2014

CC1100

Low-Power Sub- 1 GHz RF Transceiver

CC1100E

适用于中国和日本频带的低功耗低于 1GHz 无线收发器; • RF 性能 \n• 高灵敏度（1.2 kBaud、480 MHz、1% 误包率条件下为 –112 dBm）\n• 低电流消耗（1.2 kBaud、480 MHz 下 RX 中为 15.5 mA）\n• 所有支持频率下高达 +10dBm 的可编程输出功率\n• 卓越的接收机选择性和阻断性能\n• 1.2 到 500kBaud 的可编程数据速率\n• 频带：470-510 MHz 和 950- 960 MHz\n \n• 模拟特性 \n• 支持 2-FSK、GFSK、MSK 以及 OOK，灵活的 ASK 波形整形\n• 快速的锁定频率合成器以及 90 μs 的建立时间使其适合于许多跳频系统。\n• 使用自动频率补偿 (AFC) 将频率合成器调整到实际接收信号中心频率\n• 集成的模拟温度传感器\n \n• 数字特性 \n• 提供对数据包导向系统的灵活支持；同步字检测、地址校验、灵活的数据包 长度以及自动 CRC 处理的片上支持\n• 高效的 SPI 接口；利用一次“突发”数据传输便可对所有寄存器进行编程\n• 数字 RSSI 输出\n• 可编程信道滤波器带宽\n• 可编程载波监听 (CS) 指示器\n• 可编程前导质量指示器 (PQI)，用于随机噪声伪同步字检测增强保护\n• 支持发送前自动空闲信道评估 (CCA)（用于载波监听系统）\n• 支持每个数据包的链路质量指示 (LQI)\n• 可选数据自动白化和去白 (de-whitening)\n \n• 低功耗特性 \n• 400 nA 睡眠模式电流消耗\n• 快速启动时间；从睡眠模式转为 RX 或者 TX 模式只需 240 µs（由 EM 参 考设计 [3] 和 [4] 测量得出）\n• 自动低功耗 RX 轮询无线唤醒功能\n• 单独的 64 字节 RX 和 TX 数据 FIFO（实现了突发模式数据传输）\n \n• 一般特性 \n• 少量的外部组件；完全片上频率合成器，无需外部滤波器或 RF 开关\n• 绿色封装：符合 RoHS 标准，不含锑或溴\n• 小尺寸封装（QFN 4x4 mm 封装，20 引脚）\n• 适合于那些针对日本 ARIB STD-T96 标准的系统\n• 适合于那些针对中国 470-510 MHz 短距离通信设备规定的系统\n• 支持异步和同步串行接收/发送模式，以向后兼容现有无线通信协议。\n \n• APPLICATIONS \n• 运行于 470/950 MHz ISM/SRD 频带的超低功耗无线应用\n• 无线传感网络\n• 家庭和楼宇自动化\n• 高级抄表架构 (AMI)\n• 无线计量\n• 无线告警和安全系统;

CC1100E 是一款 Sub-GHz 高性能射频收发器，设计旨在用于极低功耗 RF 应用。其主要针对工业、科研和医疗 (ISM) 以及 470-510 MHz 和 950-960 MHz 频带的短距离无线通信设备 (SRD)。CC1100E 特别适合于那些针对日本 ARIB STD-T96 标准和中国 470-510 MHz 短距离通信设备的无线应用。 CC1100E 在代码、封装和外引脚方面均与 CC1101[1] 和 CC1100 [2] RF 收发 器兼容。CC1100E、CC1101 以及 CC1100 均支持互补频带，可用于全球最为 常用的开放式低于 1 GHz 频率的 RF 设计：CC1100E：470-510 MHz 和 950-960 MHzCC1101：300-348 MHz，387-464 MHz 和 779-928 MHzCC1100：300-348 MHz，400-464 MHz 和 800-928 MHzCC1100E RF 收发器与一个高度可配置的基带调制解调器集成在一起。该调制 解调器支持各种调制格式，并且拥有高达 500 kBaud 的可配置数据速率。CC1100E 可提供对数据包处理、数据缓冲、突发传输、空闲信道评估、链路质 量指示以及无线唤醒的广泛硬件支持。我们可通过一个 SPI 接口对 CC1100E 的主要运行参数和 64 字节发送/接收 FIFO 进行控制。一个典型的系统中，CC1100E 通常会与一颗微控制器以及少 数附加无源组件一起使用。

CC1100_14

Low-Power Sub- 1 GHz RF Transceiver

CC1100E

Low-Power Sub-GHz RF Transceiver(470-510 MHz & 950-960 MHz)

CC1100E

Low-Power Sub-GHz RF Transceiver

CC1100E_13

Low-Power Sub-GHz RF Transceiver

CC1100E_14

Low-Power Sub-GHz RF Transceiver