Single Supply, Rail-to-Rail Low Power FET-Input Op Amp

GENERAL DESCRIPTION The AD822 is a dual precision, low power FET input op amp that can operate from a single supply of 3.0 V to 36 V or dual supplies of ±1.5 V to ±18 V. It has true single-supply capability with an input voltage range extending below the negative rail, allowing the AD822 to acc

文件：320.84 Kbytes 页数：16 Pages

AD

亚德诺

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp

FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to 30 V Dual-supply capability from ±2.5 V to ±15 V High load drive Capacitive load drive of 350 pF, G = +1 Minimum output current of 15 mA Excellent

文件：523.63 Kbytes 页数：24 Pages

AD

亚德诺

Low Noise, Precision, Rail-to-Rail Output, JFET Single/Dual/Quad Op Amps

FEATURES Low offset voltage B grade: 0.4 mV maximum (ADA4610-1/ADA4610-2 only) A grade: 1 mV maximum Low offset voltage drift B grade: 2 μV/°C maximum (ADA4610-1/ADA4610-2 only) A grade: 8 μV/°C maximum (SOIC, MSOP, LFCSP packages) Low input bias current: 5 pA typical Dual-supply operation

文件：1.10341 Mbytes 页数：27 Pages

AD

亚德诺

MicroConverter짰 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU

文件：908.68 Kbytes 页数：88 Pages

AD

亚德诺

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp

文件：595.52 Kbytes 页数：28 Pages

AD

亚德诺

单电源、轨到轨、低功耗、FET输入双通道运算放大器

AD822是一款双通道、精密、低功耗、FET输入运算放大器，可以采用5 V至30 V单电源或±2.5 V至±15 V双电源供电。该放大器具有单电源供电能力，输入电压范围可扩展至负供电轨以下，因此它在单电源模式下可以处理地电压以下的输入信号。输出电压摆幅可扩展至各供电轨10 mV以内，以提供最大的输出动态范围。\n\n 直流精度性能包括最大800 μV的失调电压、2 μV/°C的失调电压漂移、小于25 pA的输入偏置电流以及低输入电压噪声，源阻抗最高可达1 GΩ。单位增益带宽为1.8 MHz，10 kHz时总谐波失真（THD）为–93 dB，压摆率为3 V/μs，每个放大器的电源电流低 • 真正的单电源供电\n• 轨到轨输出摆幅\n\n• 输入电压范围扩展至地电压以下\n\n• 5 V至30 V单电源供电能力\n\n• 双电源供电：±2.5 V至±15 V\n\n\n\n\n• 高负载驱动能力\n• 350 pF、G = +1的容性负载驱动能力\n\n• 最小输出电流：15 mA\n\n\n\n\n• 欲了解更多特性，请参考数据手册\n\n\nAD822-EP支持防务和航空航天应用（AQEC标准）\n• 下载AD822-EP数据手册(pdf)\n\n• 军用温度范围（−55℃至+125℃）\n\n• 受控制造基线\n\n• 封装/测试厂\n\n• 制造厂\n\n• 增强型产品;

ADI

亚德诺

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp

FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to 30 V Dual-supply capability from ±2.5 V to ±15 V High load drive Capacitive load drive of 350 pF, G = +1 Minimum output current of 15 mA Excellent

文件：523.63 Kbytes 页数：24 Pages

AD

亚德诺

JFET Input Instrumentation Amplifier with Rail-to-Rail Output in MSOP Package

GENERAL DESCRIPTION The AD8220 is the first single-supply JFET input instrumentation amplifier available in an MSOP package. Designed to meet the needs of high performance, portable instrumentation, the AD8220 has a minimum common-mode rejection ratio (CMRR) of 86 dB at dc and a minimum CMRR of

文件：1.07975 Mbytes 页数：28 Pages

AD

亚德诺

Precision, Dual-Channel Instrumentation Amplifier

GENERAL DESCRIPTION The AD8222 is a dual-channel, high performance instrumentation amplifier that requires only one external resistor per amplifier to set gains of 1 to 10,000. The AD8222 is the first dual-instrumentation amplifier in the small 4 mm × 4mm LFCSP. It requires the same board area a

文件：595.66 Kbytes 页数：24 Pages

AD

亚德诺

Low Noise, Low Gain Drift, G = 2000 Instrumentation Amplifier

GENERAL DESCRIPTION The AD8428 is an ultralow noise instrumentation amplifier designed to accurately measure tiny, high speed signals. It delivers industry-leading gain accuracy, noise, and bandwidth. All gain setting resistors for the AD8428 are internal to the part and are precisely matched. C

文件：378.74 Kbytes 页数：20 Pages

AD

亚德诺