TWL6032A2B4YFFT.A中文资料德州仪器数据手册PDF规格书

1.1 Features 1

• Five Highly Efficient Buck Converters

– One 3 MHz, 0.6 to 2.1 V at 5.0 A, DVS-Capable

– One 6 MHz, 0.6 to 2.1 V at 2.5 A, DVS-Capable

– Three 6 MHz, 0.6 to 2.1 V at 1.1 A, One Is DVS-

Capable

– Extended Mode for Higher Output Voltages

• 11 General-Purpose Low-Dropout Voltage

Regulators (LDOs)

– Six 1.0 to 3.3 V at 0.2 A With Battery or

Preregulated Supply:

• One Can be Used as Vibrator Driver

• One 1.0 to 3.3 V at 50 mA With Battery or

Preregulated Supply

• One Low-Noise 1.0 to 3.3 V at 50 mA With

Battery or Preregulated Supply

• One 3.3 V at 100 mA USB LDO

• Two LDOs for TWL6032 Internal Use

• USB OTG Module:

– ID Detection, Accessory Charger Adapter (ACA)

Support

– Accessory Detection Protocol (ADP) Support

• Backup Battery Charger

• 12-Bit Sigma-Delta Analog-to-Digital Converter

(ADC) With 19 Input Channels:

– Seven External Input Channels

• 13-Bit Coulomb Counter With Four Programmable

Integration Periods

• Low-Power Consumption:

– 8 μA in BACKUP State

– 20 μA in WAIT-ON State

– 110 μA in SLEEP State, With Two DC-DC

Converters Active

• Real-Time Clock (RTC) With Timer and Alarm

Wake-Up:

– Three Buffered 32-kHz Outputs

• SIM and SD/MMC Card Detections

• Two Digital PWM Outputs

• Thermal Monitoring:

– High-Temperature Warning

– Thermal Shutdown

• Control:

– Configurable Power-Up and Power-Down

Sequences (OTP Memory)

– Configurable Sequences Between SLEEP and

ACTIVE States (OTP Memory)

– Three Digital Output Signals that can be

Included in the Startup Sequence to Control

External Devices

– Two Inter-Integrated Circuit (I2C) Interfaces

– All Resources Configurable by I2C

• System Voltage Regulator and Battery Charger

With Power Path From USB:

– Input Current Limit to Comply With USB

Standard

– 3-MHz Switched-Mode Regulator With

Integrated Power FET for up to 2.0-A Current

– Dedicated Control Loop for Battery Current and

Voltage

– External Low-Ohmic FET for Power Path and

Battery Charging

– Boost Mode Operation for USB OTG

– Supplement Mode to Deliver Current From Battery During Power Path Operation

– Charger for Single-Cell Li-Ion and Li-Polymer

Battery Packs

– Safety Timer and Reset Control

– Thermal Protection

– Input/Output Overvoltage Protection

– Charging Indicator LED Driver

– Compliant With:

• USB 2.0

• OTG and EH 2.0

• USB Battery Charging 1.2

• YD/T 1591-2006

• Japanese Battery Charging Guidelines

(JEITA)

• Battery Voltage Range From 2.5 to 5.5 V

• Package 5.21-mm × 5.36-mm 155-Pin WCSP

1.2 Applications

• Mobile Phones and Smart Phones

• Tablets

• Gaming Handsets

• Portable Media Players

• Portable Navigation Systems

• Handheld Devices

1.3 Description

The TWL6032 device is an integrated power-management integrated circuit (PMIC) for applications

powered by a rechargeable battery. The device provides five configurable step-down converters with a

current capability of up to 5.0 A for memory, processor core, I/O, auxiliary, preregulation for LDOs, and so

forth. The device also contains nine LDO regulators for external use that can be supplied from a battery or

a preregulated supply. The power-up and power-down controller is configurable and can support any

power-up or power-down sequence (programmed in OTP memory). The RTC provides three 32-kHz clock

outputs: seconds, minutes, hours, day, month, and year information; as well as alarm wakeup and timer.

The TWL6032 device supports 32-kHz clock generation based on a crystal oscillator.

The device integrates a switched-mode system supply regulator from a USB connector. The switchedmode

regulator includes power paths from the USB and battery with supplemental mode for immediate

startup, even with an empty battery. The battery switch uses an external low-ohmic PMOS transistor

allowing minimal serial resistance during fast charging and when operating from battery. The device can

also be used without the external PMOS transistor; in this case, the battery is always tied to the system

supply and the switched-mode regulator is used for battery charging.

The TWL6032 device is available in a 155-pin WCSP package, 5.21 mm × 5.36 mm with a 0.4-mm ball

pitch.