TUSB1310AZAY集成电路（IC）的驱动器接收器收发器规格书PDF中文资料

TUSB1310AZAY属于集成电路（IC）的驱动器接收器收发器。由德州仪器制造生产的TUSB1310AZAY驱动器，接收器，收发器该系列产品的主要功能是提供必需的硬件资源，以通过延长电缆或印制线进行通信。确切的功能会因所采用的通信协议而异，可能包括诸如瞬态抑制之类的功能，这些功能对于通信用途可能并非绝对必要，但对于可能的使用环境却是明智之选。

1.1 Features

1• Universal Serial Bus (USB)

– Single Port 5.0-Gbps USB 3.0 Physical Layer

Transceiver

– One 5.0-Gbps SuperSpeed Connection

– One 480-Mbps HS/FS/LS Connection

– Fully Compliant With USB 3.0 Specification,

Revision 1.0

– Supports 3+ Meters USB 3.0 Cable Length

– Fully Adaptive Equalizer to Optimize Receiver

Sensitivity

– PIPE to Link-Layer Controller

– Supports 16-Bit SDR Mode at 250 MHz

– Compliant With PHY Interface for the USB

Architectures (PIPE), Version 3.0

– ULPI to Link-Layer Controller

– Supports 8-Bit SDR Mode at 60 MHz

– Supports Synchronous Mode and Low-Power

Mode

– Compliant With UTMI+ Low Pin Interface

(ULPI) Specification, Revision 1.1

• General Features

– IEEE 1149.1 JTAG Support

– IEEE 1149.6 JTAG support for the SuperSpeed

Port

– Operates on One Reference Clock of 40 MHz

– 3.3-, 1.8-, and 1.1-V Supply Voltages

– 1.8-V PIPE and ULPI I/O

– Available in Lead-Free 175-Ball 12- × 12-nF

NFBGA Package (ZAY)

1.2 Applications

• Surveillance Cameras

• Digital Still Cameras

• Multimedia Handsets

• Phones and Smartphones

• Portable Media Players

• Personal Navigation Devices

• Audio Docks

• Video- and Wireless-IP Phones

• Software Defined Radios

1.3 Description

The TUSB1310A device is one port, 5.0-Gbps USB 3.0 physical layer transceiver that operates off of one

reference clock, which is provided by either a crystal or an external reference clock. The reference clock

frequencies are selectable from 20, 25, 30, and 40 MHz. The TUSB1310A device provides the clock to the

USB controller. The use of one reference clock allows the TUSB1310A device to provide a cost-effective

USB 3.0 solution with few external components and a low implementation cost.

The USB controller interfaces to the TUSB1310A device through a PIPE (SuperSpeed) and a ULPI (USB

2.0) interface. The 16-bit PIPE operates off of a 250-MHz interface clock. The ULPI supports 8-bit

operations with a 60-MHz interface clock.

USB 3.0 reduces active and idle power consumption with improved power-management features. The lowpower

states of the TUSB1310A device are controlled by the USB controller through the PIPE interface.

SuperSpeed USB uses existing USB software infrastructure by keeping the existing software interfaces

and software drivers intact. In addition, SuperSpeed USB retains backward compatibility with USB 2.0

based products by using the same form-factor Type-A connector and cables. Existing USB 2.0 devices

work with new USB 3.0 hosts and new USB 3.0 devices with work with legacy USB 2.0 hosts.