TSB12LV32PZ.A中文资料德州仪器数据手册PDF规格书

FEATURES

· Compliant With IEEE 1394-1995 Standards

and 1394a-2000 Supplement for High

Performance Serial Bus1

· Supports Transfer Rates of 400, 200, or 100

Mbps

· Compatible With Texas Instruments Physical

Layer Controllers (Phys)

· Supports the Texas Instruments Bus Holder

Galvanic Isolation Barrier

· Glueless Interface to 68000 and ColdFire

Microcontrollers/Microprocessors

· Supports ColdFire Burst Transfers

· 2-Kbyte General Receive FIFO (GRF)

Accessed Through Microcontroller Interface

Supports Asynchronous and Isochronous

Receive.

· 2-Kbyte Asynchronous Transmit FIFO (ATF)

Accessed Through Microcontroller Interface

Supports Asynchronous Transmissions.

· Programmable Microcontroller Interface With

8-Bit or 16-Bit Data Bus, Multiple Modes of

Operation Including Burst Mode, and Clock

Frequency to 60 MHz

· 8-Bit or 16-Bit Data-Mover Port (DM Port)

Supports Isochronous, Asynchronous, and

Asynchronous Streaming Transmit/Receive

From an Unbuffered Port at a Clock

Frequency of 25 MHz.

· Backward Compatible With All

TSB12LV31(GPLynx) Microcontroller and

Data-Mover Functionality in Hardware

· Two-Channel Support for Isochronous

Receive to Unbuffered 8/16 Data-Mover Port

· Four-Channel Support for Isochronous

Transmit From Unbufferred 8/16 Bit

Data-Mover Port

· Single 3.3-V Supply Operation With 5-V

Tolerance Using 5-V Bias Terminals

· High Performance 100-Pin PZ Package

DESCRIPTION

The TSB12LV32 (GP2Lynx) is a high-performance general-purpose IEEE 1394a-2000 link-layer controller (LLC)

with the capability of transferring data between the 1394 Phy-link interface, an external host controller, and an

external device connected to the data-mover port (local bus interface). The 1394 Phy-link interface provides the

connection to a 1394 physical layer device and is supported by the LLC. The LLC provides the control for

transmitting and receiving 1394 packet data between the microcontroller interface and the Phy-link interface via

internal 2-Kbyte FIFOs at rates up to 400 Mbps. The TSB12LV32 transmits and receives correctly formatted

1394 packets, generates and detects the 1394 cycle start packets, communicates transaction layer transmit

requests to the Phy, and generates and inspects the 32-bit cyclic redundancy check (CRC).

The TSB12LV32 is capable of being 1394 cycle master (CM), 1394 bus manager, 1394 isochronous resource

manager (IRM) if additional control status registers (CSRs) are added via the external host controller, and

supports reception of 1394 isochronous data on two channels and transmission of 1394 isochronous data on

four channels.

The TSB12LV32 supports a direct interface to many microprocessors/microcontrollers by including

programmable endian swapping. TSB12LV32 has a generic 16-/8-bit host bus interface which includes support

for a ColdFireE microcontroller mode at rates up to 60 MHz. The microcontroller interface can operate in byte or

word (16 bit) accesses.

The data-mover block in GP2Lynx handles the external memory interface of large data blocks. This local bus

interface can be configured either to transmit or receive data packets. The packets can be either asynchronous,

isochronous, or asynchronous streaming data packets. The data-mover (DM) port can receive any type of

packet, but it can only transmit one type of packet at a time: isochronous data packets, asynchronous data

packets, or asynchronous stream data packets.

The internal FIFO is separated into an asynchronous transmit FIFO (ATF) and a general receive FIFO (GRF),

each of 520 quadlets (2 Kbytes). Asynchronous and/or isochronous receive packets can be routed to either the

DM port or the GRF via the receiver routing control logic. Asynchronous data packets or asynchronous stream

data packets can be transmitted from the DM port or the internal FIFO: ATF. If there is contention the ATF has

priority and is transmitted first. Isochronous packets can only be transmitted by the data-mover port.

The LLC also provides the capability to receive status information from the physical layer device and to access

the physical layer control and status registers by the application software.