TLK10081CTR集成电路（IC）的驱动器接收器收发器规格书PDF中文资料

TLK10081CTR属于集成电路（IC）的驱动器接收器收发器。由美国德州仪器公司制造生产的TLK10081CTR驱动器，接收器，收发器该系列产品的主要功能是提供必需的硬件资源，以通过延长电缆或印制线进行通信。确切的功能会因所采用的通信协议而异，可能包括诸如瞬态抑制之类的功能，这些功能对于通信用途可能并非绝对必要，但对于可能的使用环境却是明智之选。

1.1 Features 1

• Automatic Digital Multiplexing/De-Multiplexing

of 1 to 8 Independent Lower Speed Gigabit

Serial Lines into a Single Higher Speed Gigabit

Serial Line with Extensive Media Transmission Capabilities.

• 1~8 x (0.25 to 1.25 Gbps) to 1 x (2 to 10 Gbps)

Multiplexing

• 1 x (0.5 to 2.5 Gbps) to 1 x (0.5 to 2.5 Gbps)

• Dynamic Port Aggregation Supported

• Programmable High Speed Redundant

Switching

• Wide Data Rate Range for Multiple Application

Support

• Transmit De-Emphasis and Adaptive Receiver

Equalization on Both Low Speed and High

Speed Sides

• MDIO Clause 22 control interface

• 8B/10B ENDEC Coding Support

• Raw (Unencoded) Data Support

• Core Supply 1V; I/O: 1.5V/1.8V

• Superior Signal Integrity Performance

• Low Power Operation: < 800 mW per channel (typ)

• Rate Matching Support (For compatible data

protocols like GE PCS)

• Full Non-Blocking Receiver Crosspoint

Mapping Capability

• Flexible Clocking

• Multi Drive Capability (SFP+, backplane, cable)

• Support for Programmable High Speed Lane

Alignment Characters

• Support for Programmable HS/LS 10-Bit

Alignment Characters

• Wide Range of Built-in Test Patterns

• 144-pin, 13mmx13mm FCBGA Package

1.2 Applications

• Gigabit Serial Link Aggregation

• Communications System Backplanes

• Machine Vision

• Video/Image Data Processing

1.3 Description

The TLK10081 is a multi-rate link aggregator intended for use in high-speed bi-directional point-to-point

data transmission systems. The device allows for a reduction in the number of physical links required for a

certain data throughput by multiplexing multiple lower-rate serial links into higher-rate serial links.

The TLK10081 has a low-speed interface which can accommodate one to eight bidirectional serial links

running at rates from 250 Mbps to 1.25 Gbps (maximum of 10 Gbps total throughput). The device’s high

speed interfaces can operate at rates from 1 Gbps to 10 Gbps. The high speed interface is designed to

run at 8 x the low speed serial rate regardless of the number of lanes connected. Filler data will be placed

on any unused lanes in order to keep the interleaved lane ordering constant. This allows for low speed

lanes to be hot swapped during normal operation without requiring a change in configuration.

A 1:1 mode is also supported for data rates ranging from 0.5 Gbps to 2.5 Gbps, whereby both low speed

and high speed are rate matched. The TX and RX datapaths are also independent, so TX may operate in

8:1 mode while RX operates in 1:1 mode. This independence is restricted to using the same low speed

line rate. For example, the TX can operate at 8 x 1.25 Gbps while RX operates at 1 x 1.25 Gbps.

The individual Low Speed lanes may also operate at independent rates in byte interleave mode, provided

they are operating at integer multiples. The High Speed line rate must be configured based on the fastest

Low Speed line rate.

The device has multiple interleaving/de-interleaving schemes that may be used depending on the data

type. These schemes allow for the low speed lane ordering to be recovered after the lanes are transmitted

over a single high-speed link. There is also a programmable scrambling/de-scrambling function available

to help ensure that the high-speed data has suitable properties for transmission (i.e., sufficient transition

density for clock recovery and DC balance over time) even for non-ideal input data.

The TLK10081 has the ability to perform lane alignment on 2, 3, or 4 lanes with up to four bytes of lane

de-skew.

Both the low speed and high speed side interfaces (transmitters and receivers) use CML signaling with

integrated termination resistors and feature programmable transmitter de-emphasis levels and adaptive

receive equalization to help compensate for media impairments at higher frequencies. The device’s serial

transceivers used are capable of interfacing to optical modules as well as higher-loss connections such as

PCB backplanes and controlled-impedance copper cabling.

To aid in system synchronization, the TLK10081 is capable of extracting clocking information from the

serial input data streams and outputting a recovered clock signal. This recovered clock can be input to a

jitter cleaner in order to provide a synchronized system clock. The device also has two reference clock

input ports and a flexible internal PLL, allowing for various serial rates to be supported with a single

reference clock input frequency.

The device has various built-in self-test features to aid with system validation and debugging. Among

these are pattern generation and verification on all serial lanes as well as internal data loopback paths.