STM32F446ZC数据手册ST中文资料规格书

描述 Description

The STM32F446xC/E devices are based on the high-performance Arm® Cortex®-M4 32-bit RISC core operating at a frequency of up to 180 MHz. The Cortex-M4 core features a floating point unit (FPU) single precision supporting all Arm® single-precision data-processing instructions and data types. It also implements a full set of DSP instructions and a memory protection unit (MPU) that enhances application security.

The STM32F446xC/E devices incorporate high-speed embedded memories (Flash memory up to 512 Kbytes, up to 128 Kbytes of SRAM), up to 4 Kbytes of backup SRAM, and an extensive range of enhanced I/Os and peripherals connected to two APB buses, two AHB buses and a 32-bit multi-AHB bus matrix.

All devices offer three 12-bit ADCs, two DACs, a low-power RTC, twelve general-purpose 16-bit timers including two PWM timers for motor control, two general-purpose 32-bit timers.

They also feature standard and advanced communication interfaces.

特性 Features

• Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from Flash memory, frequency up to 180 MHz, MPU, 225 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions
• Memories
•512 Kbytes of Flash memory
•128 Kbytes of SRAM
•Flexible external memory controller with up to 16-bit data bus: SRAM, PSRAM, SDRAM/LPSDR SDRAM, NOR/NAND Flash memories
•Dual mode QuadSPI interface
• LCD parallel interface, 8080/6800 modes
• Clock, reset and supply management
•1.7 V to 3.6 V application supply and I/Os
•POR, PDR, PVD and BOR
•4 to 26 MHz crystal oscillator
•Internal 16 MHz factory-trimmed RC (1% accuracy)
•32 kHz oscillator for RTC with calibration
•Internal 32 kHz RC with calibration
• Low power
•Sleep, Stop and Standby modes
•VBAT supply for RTC, 20×32 bit backup registers plus optional 4 KB backup SRAM
• 3× 12-bit, 2.4 MSPS ADC: up to 24 channels and 7.2 MSPS in triple interleaved mode
• 2× 12-bit D/A converters
• General-purpose DMA: 16-stream DMA controller with FIFOs and burst support
• Up to 17 timers: 2x watchdog, 1x SysTick timer and up to twelve 16-bit and two 32-bit timers up to 180 MHz, each with up to four IC/OC/PWM or pulse counter
• Debug mode
•SWD and JTAG interfaces
•Cortex®-M4 Trace Macrocell™
• Up to 114 I/O ports with interrupt capability
•Up to 111 fast I/Os up to 90 MHz
•Up to 112 5 V-tolerant I/Os
• Up to 20 communication interfaces
•SPDIF-Rx
•Up to 4× I2C interfaces (SMBus/PMBus)
•Up to four USARTs and two UARTs (11.25 Mbit/s, ISO7816 interface, LIN, IrDA, modem control)
•Up to four SPIs (45 Mbits/s), three with muxed I2S for audio class accuracy via internal audio PLL or external clock
•2x SAI (serial audio interface)
•2× CAN (2.0B Active)
•SDIO interface
•Consumer electronics control (CEC) I/F
• Advanced connectivity
•USB 2.0 full-speed device/host/OTG controller with on-chip PHY
•USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI
•Dedicated USB power rail enabling on-chip PHYs operation throughout the entire MCU power supply range
• 8- to 14-bit parallel camera interface up to 54 Mbytes/s
• CRC calculation unit
• RTC: subsecond accuracy, hardware calendar
• 96-bit unique ID