ST25R3918数据手册RF/IF射频/中频RFID的RFID射频接入监控IC规格书PDF

描述 Description

The ST25R3918 is a multipurpose NFC transceiver supporting NFC reader, passive peer to peer functionality and NFC card emulation mode.

This IC is optimized for IOT and other consumer or industrial applications where excellent analog performance is required.

The ST25R3918 is also optimized to achieve good read ranges with low output power, even under noisy and harsh environments, using noise reduction receiver technology.

This IC offers an advanced analog front end (AFE) and a highly integrated data framing system for NFC-A/B (ISO 14443A/B) reader including higher bit rates. NFC-V (ISO 15693) reader is supported up to 53 kbps via streaming mode to read cards.

ISO 18092 passive initiator and target and NFC-A / NFC-F card emulation are also available to ensure communication between end products. This enables device programming or simple NDEF data transfers to interact with Android™ phones or to use Apple® App Clips.

Special stream and transparent modes of the AFE and framing system can be used to implement other custom protocols in reader or card emulation mode.

The ST25R3918 includes a low power wakeup mode to scan for the presence of a card by performing a measurement of the amplitude or phase of the antenna signal. It also contains a low power RC oscillator and wake-up timer to automatically trigger the device after the configured time period and check for a presence of a tag.

The ST25R3918 is designed to operate from a wide power supply range (2.6 to 5.5 V from -40 °C to +105 °C, 2.4 to 5.5 V from -20 °C to +105 °C), and a wide peripheral IO voltage range (from 1.65 to 5.5 V).

特性 Features

• Operating modes
•Reader/writer
•Card emulation
•Passive peer to peer
• RF communication
•NFC-A / ISO14443A up to 848 kbit/s
•NFC-B / ISO14443B up to 848 kbit/s
•NFC-V / ISO15693 up to 53 kb/s
•NFC-A / ISO14443A and NFC-F / FeliCa™ card emulation
•Low level modes to implement MIFARE Classic® compliant or other custom protocols
• 主要特性
•Dynamic power output (DPO) controls the field strength to stay within given limits
•Active wave shaping (AWS) reduces over-and under-shoots
•Noise suppression receiver (NSR) allows reception in noisy environment
•Automatic gain control and squelch feature to maximize SNR
•Low power inductive card detection
•Low power NFC passive target modes
•Adjustable ASK modulation depth, from 5 to 40%
•Integrated regulators to boost system PSRR
•AM/PM and I/Q demodulator with baseband channel summation or automatic channel selection
•Possibility to drive two independent single ended antennas
•Measurement of antenna voltage amplitude and phase, RSSI, on-chip supply and regulated voltages
• External communication interfaces
•512-byte FIFO
•Serial peripheral interface (SPI) up to 10 Mbit/s
•I2C with up to 400 kbit/s in Fast-mode, 1 Mbit/s in Fast-mode Plus, and 3.4 Mbit/s in High-speed mode
• Electrical characteristics
•Wide supply voltage and ambient temperature range (2.6 to 5.5 V from -40 °C to +105 °C, 2.4 to 5.5 V from -20 °C to +105 °C)
•Wide peripheral communication supply range, from 1.65 to 5.5 V
•Quartz oscillator capable of operating with 27.12 MHz crystal with fast start-up

简介

ST25R3918属于RF/IF射频/中频RFID的RFID射频接入监控IC。由制造生产的ST25R3918RFID，射频接入，监控 ICRFID 或射频接入监控 IC 是配置为射频识别 (RFID) 读取器、应答器、无源接入/无源启动处理器和轮胎压力监测系统 (TPMS) 的半导体器件。这些器件的设计符合 EPC、ISO、NFC、MiFARE 和 FeliCa 等特定 RFID 标准，并通过 I2C、SPI、UART、USB、PWM、RS232、RS422、RS485 及其他接口进行通信。