SN74LVTH162373DLR集成电路（IC）的锁存器规格书PDF中文资料

SN74LVTH162373DLR属于集成电路（IC）的锁存器。由德州仪器制造生产的SN74LVTH162373DLR锁存器锁存器是类似于触发器的基本数字存储设备，但是不同之处在于，在锁存使能（或类似命名）信号处于有效逻辑状态的任何时间，保持的逻辑状态都可以改变。“透明”锁存器还允许设备输出在锁存使能信号有效时反映输入的当前状态，而相反的是，状态仅在保持状态已固定时改变。

FEATURES

· Members of the Texas Instruments Widebus™

Family

· Output Ports Have Equivalent 22-W Series

Resistors, So No External Resistors Are

Required

· Support Mixed-Mode Signal Operation (5-V

Input and Output Voltages With 3.3-V VCC)

· Support Unregulated Battery Operation Down

to 2.7 V

· Typical VOLP (Output Ground Bounce) <0.8 V

at VCC = 3.3 V, TA = 25°C

· Ioff and Power-Up 3-State Support Hot

Insertion

· Bus Hold on Data Inputs Eliminates the Need

for External Pullup/Pulldown Resistors

· Distributed VCC and GND Pins Minimize

High-Speed Switching Noise

· Flow-Through Architecture Optimizes PCB

Layout

· Latch-Up Performance Exceeds 500 mA Per

JESD 17

· ESD Protection Exceeds JESD 22

– 2000-V Human-Body Model (A114-A)

– 200-V Machine Model (A115-A)

DESCRIPTION/ORDERING INFORMATION

The 'LVTH162373 devices are16-bit transparent D-type latches with 3-state outputs designed for low-voltage

(3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These

devices are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and

working registers.

A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or

low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the

bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines

without interface or pullup components.

OE does not affect internal operations of the latch. Old data can be retained or new data can be entered while

the outputs are in the high-impedance state.

The outputs, which are designed to source or sink up to 12 mA, include equivalent 22-W series resistors to

reduce overshoot and undershoot.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown

resistors with the bus-hold circuitry is not recommended.

When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down.

However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor;

the minimum value of the resistor is determined by the current-sinking capability of the driver.

These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry

disables the outputs, preventing damaging current backflow through the devices when they are powered down.

The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,

which prevents driver conflict.

These devices can be used as two 8-bit latches or one 16-bit latch. When the latch-enable (LE) input is high, the

Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels set up at the

D inputs.