SN74GTLP817DWR集成电路（IC）的转换器电平移位器规格书PDF中文资料

SN74GTLP817DWR属于集成电路（IC）的转换器电平移位器。由美国德州仪器公司制造生产的SN74GTLP817DWR转换器，电平移位器逻辑转换器或电平移位器 IC 可用于在数字逻辑设备之间传递信息，这些设备可在不同/不兼容的供电电压下工作，或可实现不同的信令方式。例如，可以将需要 5 V 电源的数字输出传感器连接到具有 3.3 V I/O 电源的 FPGA，或者在 CMOS 或 TTL 等单端信令方式与 PECL 或 LVDS 等差分技术之间进行转换。

FEATURES

· OEC™ Circuitry Improves Signal Integrity and

Reduces Electromagnetic Interference

· Bidirectional Interface Between GTLP Signal

Levels and LVTTL Logic Levels

· GTLP-to-LVTTL 1-to-6 Fanout Driver

· LVTTL-to-GTLP 1-to-2 Fanout Driver

· LVTTL Interfaces Are 5-V Tolerant

· Medium-Drive GTLP Outputs (50 mA)

· Reduced-Drive LVTTL Outputs

(–12 mA/12 mA)

· Variable Edge-Rate Control (ERC) Input

Selects GTLP Rise and Fall Times for Optimal

Data-Transfer Rate and Signal Integrity in

Distributed Loads

· Ioff and Power-Up 3-State Support Hot

Insertion

· Distributed VCC and GND Pins Minimize

High-Speed Switching Noise

· Latch-Up Performance Exceeds 100 mA Per

JESD 78, Class II

· ESD Protection Exceeds JESD 22

– 2000-V Human-Body Model (A114-A)

– 200-V Machine Model (A115-A)

– 1000-V Charged-Device Model (C101)

DESCRIPTION/ORDERING INFORMATION

The SN74GTLP817 is a medium-drive fanout driver that provides LVTTL-to-GTLP and GTLP-to-LVTTL

signal-level translation. The device provides a high-speed interface between cards operating at LVTTL logic

levels and a backplane operating at GTLP signal levels. High-speed (about three times faster than standard TTL

or LVTTL) backplane operation is a direct result of GTLP reduced output swing (<1 V), reduced input threshold

levels, improved differential input, and OEC™ circuitry. The improved GTLP OEC circuitry minimizes bus settling

time and has been designed and tested using several backplane models. The medium drive allows incident-wave

switching in heavily loaded backplanes with equivalent load impedance down to 19 W. BO1 and BO2 can be tied

together to drive an equivalent load impedance down to 11 W.

GTLP is the Texas Instruments (TI™) derivative of the Gunning Transceiver Logic (GTL) JEDEC standard

JESD 8-3. The ac specification of the SN74GTLP817 is given only at the preferred higher noise-margin GTLP,

but the user has the flexibility of using this device at either GTL (VTT = 1.2 V and VREF = 0.8 V) or GTLP

(VTT = 1.5 V and VREF = 1 V) signal levels.

Normally, the B port operates at GTLP signal levels. The A-port and control inputs operate at LVTTL logic levels,

but are 5-V tolerant and are compatible with TTL and 5-V CMOS inputs. VREF is the B-port differential input

reference voltage.

GNDT is the TTL output ground, while GNDG is the GTLP output ground, and both may be separated from each

other for a quieter device.

This device is fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry

disables the outputs, preventing damaging current backflow through the device when it is powered down. The

power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,

which prevents driver conflict.

This device features adjustable edge-rate control (ERC). Changing the ERC input voltage between GND and VCC

adjusts the B-port output rise and fall times. This allows the designer to optimize system data-transfer rate and

signal integrity to the backplane load. ERC automatically is selected to the same speed as alternate source

1-to-6 fanout drivers that use pin 18 for 3.3-V or 5-V VCC.

When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down.

However, to ensure the high-impedance state above 1.5 V, the output-enable (OE) input should be tied to VCC

through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the

driver.