SN74AVCH4T245PW集成电路（IC）的缓冲器驱动器接收器收发器规格书PDF中文资料

SN74AVCH4T245PW属于集成电路（IC）的缓冲器驱动器接收器收发器。由德州仪器制造生产的SN74AVCH4T245PW缓冲器，驱动器，接收器，收发器逻辑缓冲器、驱动器、接收器和收发器允许隔离对某个电路的逻辑信号的访问，以用于另一电路。缓冲器将其输入信号（不变或反相）传递到其输出，并可能用于清除弱信号或驱动负载。在布尔逻辑仿真器中，缓冲器主要用于增加传播延迟。逻辑接收器和收发器允许在数据总线之间进行隔离通信。

1 Features

• Control inputs VIH/VIL levels are referenced to

VCCA voltage

• Fully configurable dual-rail design allows each port

to operate over the full 1.2V to 3.6V power-supply

range

• I/Os Are 4.6V Tolerant

• Ioff supports partial power-down-mode operation

• Bus hold on data inputs eliminates the need for

external pull-up/pull-down resistors

• Supports data rate up to:

– 380Mbps (1.8V to 3.3V Translation)

– 200Mbps (<1.8V to 3.3V Translation)

– 200Mbps (Translate to 2.5V or 1.8V)

– 150Mbps (Translate to 1.5V)

– 100Mbps (Translate to 1.2V)

• Latch-up performance exceeds 100mA per JESD

78, class II

• ESD protection exceeds JESD 22:

– 8000V Human Body Model (A114-A)

– 200V Machine Model (A115-A)

– 1000V Charged-Device Model (C101)

2 Applications

• Personal electronics

• Industrial

• Enterprise

• Telecom

3 Description

This 4-bit noninverting bus transceiver uses two

separate configurable power-supply rails. The A port

is designed to track VCCA. VCCA accepts any supply

voltage from 1.2V to 3.6V. The B port is designed

to track VCCB. VCCB accepts any supply voltage from

1.2V to 3.6V. The SN74AVCH4T245 is optimized

to operate with VCCA/VCCB set at 1.2V to 3.6V.

It is operational with VCCA/VCCB as low as 1.2V.

This allows for universal low voltage bidirectional

translation between any of the 1.2V, 1.5V, 1.8V, 2.5V,

and 3.3V voltage nodes.

The SN74AVCH4T245 is designed for asynchronous

communication between two data buses. The logic

levels of the direction-control (DIR) input and the

output-enable (OE) input activate either the B-port

outputs or the A-port outputs or place both output

ports into the high-impedance mode. The device

transmits data from the A bus to the B bus when the

B-port outputs are activated, and from the B bus to

the A bus when the A-port outputs are activated. The

input circuitry on both A and B ports is always active

and must have a logic HIGH or LOW level applied to

prevent excess ICC and ICCZ.

The SN74AVCH4T245 device control pins (1DIR,

2DIR, 1OE, and 2OE) are supplied by VCCA.

This device is fully specified for partial-power-down

applications using Ioff. The Ioff circuitry disables

the outputs, preventing damaging current backflow

through the device when it is powered down.

The VCC isolation feature is designed so that if either

VCC input is at GND, then both ports are in the

high-impedance state. The bus-hold circuitry on the

powered-up side always stays active.

Active bus-hold circuitry holds unused or undriven

data inputs at a valid logic state. Use of pull-up or

pull-down resistors with the bus-hold circuitry is not

recommended. The bus-hold circuitry on the poweredup

side always stays active.

To put the device in the high-impedance state

during power up or power down, tie the OE pin to

VCC through a pull-up resistor; the current-sinking

capability of the driver determines the minimum value

of the resistor.