SN74AVCBH164245VR集成电路（IC）的转换器电平移位器规格书PDF中文资料

SN74AVCBH164245VR属于集成电路（IC）的转换器电平移位器。由美国德州仪器公司制造生产的SN74AVCBH164245VR转换器，电平移位器逻辑转换器或电平移位器 IC 可用于在数字逻辑设备之间传递信息，这些设备可在不同/不兼容的供电电压下工作，或可实现不同的信令方式。例如，可以将需要 5 V 电源的数字输出传感器连接到具有 3.3 V I/O 电源的 FPGA，或者在 CMOS 或 TTL 等单端信令方式与 PECL 或 LVDS 等差分技术之间进行转换。

1FEATURES

2· Member of the Texas Instruments

Widebus™ Family

· Dynamic Output Control (DOC™) Circuitry

Dynamically Changes Output Impedance,

Resulting in Noise Reduction Without Speed

Degradation

· Dynamic Drive Capability Is Equivalent to

Standard Outputs With IOH and IOL of ±24 mA at

2.5-V VCC

· Control Inputs VIH/VIL Levels are Referenced to

VCCB Voltage

· If Either VCC Input Is at GND, Both Ports Are in

the High-Impedance State

· Overvoltage-Tolerant Inputs/Outputs Allow

Mixed-Voltage-Mode Data Communications

· Ioff Supports Partial-Power-Down Mode

Operation

· Fully Configurable Dual-Rail Design Allows

Each Port to Operate Over the Full 1.4-V to

3.6-V Power-Supply Range

· Bus Hold on Data Inputs Eliminates the Need

for External Pullup/Pulldown Resistors

· Latch-Up Performance Exceeds 100 mA Per

JESD 78, Class II

· ESD Protection Exceeds JESD 22

– 2000-V Human-Body Model (A114-A)

– 200-V Machine Model (A115-A)

– 1000-V Charged-Device Model (C101)

DESCRIPTION/ORDERING INFORMATION

This 16-bit (dual-octal) noninverting bus transceiver uses two separate configurable power-supply rails. The

A-port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B-port is designed to

track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage

bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.

The SN74AVCBH164245 is designed for asynchronous communication between data buses. The device

transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the

direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are

effectively isolated.

The SN74AVCBH164245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or

pulldown resistors with the bus-hold circuitry is not recommended.

To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup

resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,

preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND,

both ports are in the high-impedance state.