SC28L194A1BE中文资料Quad UART for 3.3 V and 5 V supply voltage数据手册恩XP规格书

描述 Description

The Philips 28L194 Quad UART is a single chip CMOS-LSI communications device that provides 4 full-duplex asynchronous channels with significantly deeper 16 byte FIFOs, Automatic in-band flow control using Xon/Xoff characters defined by the user and address recognition in the Wake-up mode. Synchronous bus interface is used for all communication between host and QUART. It is fabricated in Philips state of the art CMOS technology that combines the benefits of low cost, high density and low power consumption.
The operating speed of each receiver and transmitter can be selected independently from one of 22 fixed baud rates, a 16X clock derived from one of two programmable baud rate counters or one of three external 16X clocks (1 available at 1x clock rate). The baud rate generator and counter can operate directly from a crystal or from seven other external or internal clock inputs. The ability to independently program the operating speed of the receiver and transmitter makes the Quad UART particularly attractive for dual speed full duplex channel applications such as clustered terminal systems. The receivers and transmitters are buffered with FIFOs of 16 characters to minimize the potential for receiver overrun and to reduce interrupt overhead. In addition, a handshaking capability and in-band flow control are provided to disable a remote UART transmitter when the receiver buffer is full or nearly so.
To minimize interrupt overhead an interrupt arbitration system is included which reports the context of the interrupting UART via direct access or through the modification of the interrupt vector. The context of the interrupt is reported as channel number, type of device interrupting (receiver COS etc.) and, for transmitters or receivers, the fill level of the FIFO.
The Quad UART provides a power down mode in which the oscillator is stopped but the register contents are maintained. This results in reduced power consumption of several orders of magnitudes. The Quad UART is fully TTL compatible when operating from a single +5V or 3.3V power supply. Operation at 3.3V or 5.0V is maintained with CMOS interface levels.

特性 Features

Single 3.3V and 5.0V power supply
Four Philips industry standard full duplex UART channels
Sixteen byte receiver FIFOs for each UART
Sixteen byte transmit FIFOs for each UART
In band flow control using programmable Xon/Xoff characters
Flow control using CTSN RTSN hardware handshaking
Automatic address detection in multi-drop mode
Three byte general purpose character recognition
Fast data bus, 15 ns data bus release time, 125 ns bus cycle time
Programmable interrupt priorities
Automatic identification of highest priority interrupt pending
Global interrupt and control registers ease setup and interrupt handling
Vectored interrupts with programmable interrupt vector formats Interrupt vector modified with channel number
Interrupt vector modified with channel number and channel type
Interrupt vector not modified
IACKN and DACKN signal pins
Watch dog timer for each receiver (64 receive clock counts)
Programmable Data Formats: 5 to 8 data bits plus parity
Odd, even force or no parity
1, 1.5 or 2 stop bits
Flexible baud rate selection for receivers and transmitters: 22 fixed rates; 50 - 230.4K baud or 100 to 460.8K baud
Additional non-standard rates to 500K baud with internal generators
Two reload-counters provide additional programmable baud rate generation
External 1x or 16x clock inputs
Simplified baud rate selection
1 MHz 1x and 16x data rates full duplex all channels.
Parity, framing and overrun error detection
False start bit detection
Line break detection and generation
Programmable channel mode Normal(full duplex)
Diagnostic modes
automatic echo
local loop back
remote loop back

Four I/O ports per UART for modem controls, clocks, RTSN, I/O, etc. All I/O ports equipped with 'Change of State Detectors'
Two global inputs and two global outputs for general purpose I/O
Power down mode
On chip crystal oscillator, 2-8 MHz
TTL input levels. Outputs switch between full V CC and V SS
High speed CMOS technology
80-pin Low Profile Quad Flat Pack LQFP and 68-pin PLCC

应用 Application

Statistical Multiplexers
Data Concentrators Packet-switching networks
Process Control
Building or Plant Control
Laboratory data gathering
ISDN front ends
Computer Networks
Point-of-Sale terminals

Automotive, cab and engine controls
Entertainment systems MIDDI keyboard control music systems
Theater lighting control

Terminal Servers Computer-Printer/Plotter links