SC16IS760

Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

SC16IS760IBS

Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support; General features\nSingle full-duplex UART\nSelectable I²C-bus or SPI interface\n3.3 V or 2.5 V operation\nIndustrial temperature range: -40 ºC to +95 ºC\n64 bytes FIFO (transmitter and receiver)\nFully compatible with industrial standard 16C450 and equivalent\nBaud rates up to 5 Mbit/s in 16× clock mode\nAuto hardware flow control using RTS/CTS\nAuto software flow control with programmable Xon/Xoff characters\nSingle or double Xon/Xoff characters\nAutomatic RS-485 support (automatic slave address detection)\nUp to eight programmable I/O pins (SC16IS750 and SC16IS760 only)\nRS-485 driver direction control via RTS signal\nRS-485 driver direction control inversion\nBuilt-in IrDA encoder and decoder interface\nSC16IS750 supports IrDA SIR with speeds up to 115.2 kbit/s\nSC16IS760 supports IrDA SIR with speeds up to 1.152 Mbit/s\nSoftware reset\nTransmitter and receiver can be enabled/disabled independent of each other\nReceive and Transmit FIFO levels\nProgrammable special character detection\nFully programmable character formatting 5-bit, 6-bit, 7-bit or 8-bit character\nEven, odd, or no parity\n1, 1½, or 2 stop bits\nLine break generation and detection\nInternal Loopback mode\nSleep current less than 30 µA at 3.3 V\nIndustrial and commercial temperature ranges\nAvailable in HVQFN24, TSSOP24 (SC16IS750/760) and TSSOP16 (SC16IS740) packages\nI²C-bus features\nNoise filter on SCL/SDA inputs\n400 kbit/s maximum speed\nCompliant with I²C-bus fast speed\nSlave mode only\nSPI features\nSC16IS750 supports 4 Mbit/s maximum SPI clock speed\nSC16IS760 supports 15 Mbit/s maximum SPI clock speed\nSlave mode only\nSPI Mode 0\n;

The SC16IS740/750/760 is a slave I²C-bus/SPI interface to a single-channel high performance UART. It offers data rates up to 5 Mbit/s and guarantees low operating and sleeping current. The SC16IS750 and SC16IS760 also provide the application with 8 additional programmable I/O pins. The device comes in very small HVQFN24, TSSOP24 (SC16IS750/760) and TSSOP16 (SC16IS740) packages, which makes it ideally suitable for handheld, battery operated applications. This family of products enables seamless protocol conversion from I²C-bus or SPI to and RS-232/RS-485 and are fully bidirectional.\nThe SC16IS760 differs from the SC16IS750 in that it supports SPI clock speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the SC16IS750, and in that it supports IrDA SIR up to 1.152 Mbit/s. In all other aspects, the SC16IS760 is functionally and electrically the same as the SC16IS750. The SC16IS740 is functionally and electrically identical to the SC16IS750, with the exception of the programmable I/O pins which are only present on the SC16IS750.\nThe SC16IS740/750/760’s internal register set is backward-compatible with the widely used and widely popular 16C450. This allows the software to be easily written or ported from another platform.\nThe SC16IS740/750/760 also provides additional advanced features such as auto hardware and software flow control, automatic RS-485 support, and software reset. This allows the software to reset the UART at any moment, independent of the hardware reset signal.\n

SC16IS760IPW

Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support; General features\nSingle full-duplex UART\nSelectable I²C-bus or SPI interface\n3.3 V or 2.5 V operation\nIndustrial temperature range: -40 ºC to +95 ºC\n64 bytes FIFO (transmitter and receiver)\nFully compatible with industrial standard 16C450 and equivalent\nBaud rates up to 5 Mbit/s in 16× clock mode\nAuto hardware flow control using RTS/CTS\nAuto software flow control with programmable Xon/Xoff characters\nSingle or double Xon/Xoff characters\nAutomatic RS-485 support (automatic slave address detection)\nUp to eight programmable I/O pins (SC16IS750 and SC16IS760 only)\nRS-485 driver direction control via RTS signal\nRS-485 driver direction control inversion\nBuilt-in IrDA encoder and decoder interface\nSC16IS750 supports IrDA SIR with speeds up to 115.2 kbit/s\nSC16IS760 supports IrDA SIR with speeds up to 1.152 Mbit/s\nSoftware reset\nTransmitter and receiver can be enabled/disabled independent of each other\nReceive and Transmit FIFO levels\nProgrammable special character detection\nFully programmable character formatting 5-bit, 6-bit, 7-bit or 8-bit character\nEven, odd, or no parity\n1, 1½, or 2 stop bits\nLine break generation and detection\nInternal Loopback mode\nSleep current less than 30 µA at 3.3 V\nIndustrial and commercial temperature ranges\nAvailable in HVQFN24, TSSOP24 (SC16IS750/760) and TSSOP16 (SC16IS740) packages\nI²C-bus features\nNoise filter on SCL/SDA inputs\n400 kbit/s maximum speed\nCompliant with I²C-bus fast speed\nSlave mode only\nSPI features\nSC16IS750 supports 4 Mbit/s maximum SPI clock speed\nSC16IS760 supports 15 Mbit/s maximum SPI clock speed\nSlave mode only\nSPI Mode 0\n;

The SC16IS740/750/760 is a slave I²C-bus/SPI interface to a single-channel high performance UART. It offers data rates up to 5 Mbit/s and guarantees low operating and sleeping current. The SC16IS750 and SC16IS760 also provide the application with 8 additional programmable I/O pins. The device comes in very small HVQFN24, TSSOP24 (SC16IS750/760) and TSSOP16 (SC16IS740) packages, which makes it ideally suitable for handheld, battery operated applications. This family of products enables seamless protocol conversion from I²C-bus or SPI to and RS-232/RS-485 and are fully bidirectional.\nThe SC16IS760 differs from the SC16IS750 in that it supports SPI clock speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the SC16IS750, and in that it supports IrDA SIR up to 1.152 Mbit/s. In all other aspects, the SC16IS760 is functionally and electrically the same as the SC16IS750. The SC16IS740 is functionally and electrically identical to the SC16IS750, with the exception of the programmable I/O pins which are only present on the SC16IS750.\nThe SC16IS740/750/760’s internal register set is backward-compatible with the widely used and widely popular 16C450. This allows the software to be easily written or ported from another platform.\nThe SC16IS740/750/760 also provides additional advanced features such as auto hardware and software flow control, automatic RS-485 support, and software reset. This allows the software to reset the UART at any moment, independent of the hardware reset signal.\n

SC16IS760IBS

Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

SC16IS760IPW

Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support