SC16IS752

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

ETC

SC16IS752

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

ETC

SC16IS752

Smart, simple solutions for the 12 most common design concerns

ETC

SC16IS752IBS

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support; General featuresDual full-duplex UART\nI²C-bus or SPI interface selectable\n3.3 V or 2.5 V operation\nIndustrial temperature range: -40 °C to +95 °C\n64 bytes FIFO (transmitter and receiver)\nFully compatible with industrial standard 16C450 and equivalent\nBaud rates up to 5 Mbit/s in 16× clock mode\nAuto hardware flow control using RTS/CTS\nAuto software flow control with programmable Xon/Xoff characters\nSingle or double Xon/Xoff characters\nAutomatic RS-485 support (automatic slave address detection)\nUp to eight programmable I/O pins\nRS-485 driver direction control via RTS signal\nRS-485 driver direction control inversion\nBuilt-in IrDA encoder and decoder supporting IrDA SIR with speeds up to 115.2 kbit/s\nSC16IS762 supports IrDA SIR with speeds up to 1.152 Mbit/s\nSoftware reset\nTransmitter and receiver can be enabled/disabled independent of each other\nReceive and Transmit FIFO levels\nProgrammable special character detection\nFully programmable character formatting 5-bit, 6-bit, 7-bit or 8-bit character\nEven, odd, or no parity\n1, 1½, or 2 stop bits\nLine break generation and detection\nInternal Loopback mode\nSleep current less than 30 μA at 3.3 V\nIndustrial and commercial temperature ranges\n5 V tolerant inputs\nAvailable in HVQFN32 and TSSOP28 packages\nI²C-bus featuresNoise filter on SCL/SDA inputs\n400 kbit/s (maximum)\nCompliant with I²C-bus Fast mode\nSlave mode only\nSPI featuresSC16IS752 supports 4 Mbit/s maximum SPI clock speed\nSC16IS762 supports 15 Mbit/s maximum SPI clock speed\nSlave mode only\nSPI Mode 0\n;

The SC16IS752/SC16IS762 is an I²C-bus/SPI bus interface to a dual-channel high performance UART offering data rates up to 5 Mbit/s, low operating and sleeping current; it also provides the application with 8 additional programmable I/O pins. The device comes in very small HVQFN32 and TSSOP28 packages, which makes it ideally suitable for hand-held, battery-operated applications. This chip enables seamless protocol conversion from I²C-bus/SPI to RS-232/RS-485 and is fully bidirectional.\nThe SC16IS762 differs from the SC16IS752 in that it supports SPI clock speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the SC16IS752, and in that it supports IrDA SIR up to 1.152 Mbit/s. In all other aspects, the SC16IS762 is functionally and electrically the same as the SC16IS752.\nThe SC16IS752/SC16IS762’s internal register set is backward compatible with the widely used and widely popular 16C450. This allows the software to be easily written or ported from another platform.\nThe SC16IS752/SC16IS762 also provides additional advanced features such as auto hardware and software flow control, automatic RS-485 support and software reset. This allows the software to reset the UART at any moment, independent of the hardware reset signal.\n

恩XP

SC16IS752IPW

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support; General featuresDual full-duplex UART\nI²C-bus or SPI interface selectable\n3.3 V or 2.5 V operation\nIndustrial temperature range: -40 °C to +95 °C\n64 bytes FIFO (transmitter and receiver)\nFully compatible with industrial standard 16C450 and equivalent\nBaud rates up to 5 Mbit/s in 16× clock mode\nAuto hardware flow control using RTS/CTS\nAuto software flow control with programmable Xon/Xoff characters\nSingle or double Xon/Xoff characters\nAutomatic RS-485 support (automatic slave address detection)\nUp to eight programmable I/O pins\nRS-485 driver direction control via RTS signal\nRS-485 driver direction control inversion\nBuilt-in IrDA encoder and decoder supporting IrDA SIR with speeds up to 115.2 kbit/s\nSC16IS762 supports IrDA SIR with speeds up to 1.152 Mbit/s\nSoftware reset\nTransmitter and receiver can be enabled/disabled independent of each other\nReceive and Transmit FIFO levels\nProgrammable special character detection\nFully programmable character formatting 5-bit, 6-bit, 7-bit or 8-bit character\nEven, odd, or no parity\n1, 1½, or 2 stop bits\nLine break generation and detection\nInternal Loopback mode\nSleep current less than 30 μA at 3.3 V\nIndustrial and commercial temperature ranges\n5 V tolerant inputs\nAvailable in HVQFN32 and TSSOP28 packages\nI²C-bus featuresNoise filter on SCL/SDA inputs\n400 kbit/s (maximum)\nCompliant with I²C-bus Fast mode\nSlave mode only\nSPI featuresSC16IS752 supports 4 Mbit/s maximum SPI clock speed\nSC16IS762 supports 15 Mbit/s maximum SPI clock speed\nSlave mode only\nSPI Mode 0\n;

The SC16IS752/SC16IS762 is an I²C-bus/SPI bus interface to a dual-channel high performance UART offering data rates up to 5 Mbit/s, low operating and sleeping current; it also provides the application with 8 additional programmable I/O pins. The device comes in very small HVQFN32 and TSSOP28 packages, which makes it ideally suitable for hand-held, battery-operated applications. This chip enables seamless protocol conversion from I²C-bus/SPI to RS-232/RS-485 and is fully bidirectional.\nThe SC16IS762 differs from the SC16IS752 in that it supports SPI clock speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the SC16IS752, and in that it supports IrDA SIR up to 1.152 Mbit/s. In all other aspects, the SC16IS762 is functionally and electrically the same as the SC16IS752.\nThe SC16IS752/SC16IS762’s internal register set is backward compatible with the widely used and widely popular 16C450. This allows the software to be easily written or ported from another platform.\nThe SC16IS752/SC16IS762 also provides additional advanced features such as auto hardware and software flow control, automatic RS-485 support and software reset. This allows the software to reset the UART at any moment, independent of the hardware reset signal.\n

恩XP

SC16IS752IBS

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

ETC

SC16IS752IBS

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

ETC

SC16IS752IPW

Dual UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support

ETC