SAM9X60SIP中文资料微芯科技数据手册PDF规格书

特性 Features

• CPU

– ARM926EJ-S Arm Thumb processor running up to 600 MHz

– 32-Kbyte data cache, 32-Kbyte instruction cache, Memory Management Unit (MMU)

• Memories

– One 160-Kbyte internal ROM

• 64-Kbyte internal ROM embedding a secure bootloader program supporting boot on NandFlash,

SDCard, SPI or QSPI Flash. Bootloader features selectable by OTP bits.

• 96-Kbyte ROM for NAND Flash BCH ECC table

– DDR2-SDRAM memory up to 1 Gbit or 64-Mbit SDR-SDRAM memory, 16-bit data bus

– One 64-Kbyte internal SRAM (SRAM0), single-cycle access at system speed

– High Bandwidth Multi-port DDR2/LPDDR Controller (MPDDRC)

– 8-bit External Bus Interface (EBI) supporting 8-bit NAND Flash connected on D16-D23

– NAND Flash Controller, with up to 24-bit Programmable Multi-bit Error Correcting Code (PMECC)

– One 11-Kbyte OTP memory for secure key storage with emulation mode (OTP bits are emulated by a

4-Kbyte SRAM (SRAM1))

• System Running up to 200 MHz

– Power-on Reset cells, Reset Controller, Shutdown Controller, Periodic Interval Timer, Watchdog Timer

running on internal low-power 32-kHz RC and Real Time Clock running on external crystal

– Two internal trimmed RC oscillators: 32 kHz (low-power) and 12 MHz

– Two selectable crystal oscillators: 32.768 kHz (low-power) and 8 to 50 MHz

– One PLL for the system and one PLL optimized for USB high-speed operation (480 MHz)

– One dual-port 16-channel DMA Controller (XDMAC)

– Advanced Interrupt Controller (AIC) and Debug Unit (DBGU)

– JTAG port with disable bit in OTP memory

– Two programmable external clock signals

• Low Power Modes

– Backup mode with RTC, eight 32-bit general purpose backup registers, and Shutdown Controller to control

the external power supply

– Clock Generator and Power Management Controller

– Software-programmable Ultra-Low Power modes: Very Slow Clock Operating Mode (ULP0), and No-Clock

Operating Mode (ULP1) with fast wake-up capabilities

– Software programmable power optimization capabilities

• Peripherals

– LCD Controller with overlay, alpha-blending, rotation, scaling and color conversion. Up to 1024 x 768

resolution

– 2D Graphics Controller supporting Fill BLT, Copy BLT, Transparent BLT, Blend/Alpha BLT, ROP4 BLT

(Raster Operations) and Command Ring Buffer

– ITU-R BT. 601/656, up to 12-bit Image Sensor Interface (ISI)

– One USB Device High Speed, three USB Host High Speed with dedicated On-Chip Transceivers

– Two 10/100 Mbps Ethernet Mac Controller

– Two 4-bit Secure Digital MultiMedia Card Controller (SDMMC)

– Two CAN Controllers

– One Quad I/O SPI Controller

– Two three-channel 32-bit Timer/Counters

– One high resolution (64-bit) Periodic Interval Timer

– One Synchronous Serial Controller

– One Inter-IC Sound (I²S) Multi-Channel Controller (I2SMCC) with TDM support

– One Audio Class D Controller with Single-Ended (SE) or Bridge Tied Load (BTL) connection to power stage

– One four-channel 16-bit PWM Controller

– Thirteen FLEXCOMs (USART, SPI and TWI)

– One 12-channel 12-bit Analog-to-Digital Converter with 4/5 wires resistive touchscreen support

• Hardware Cryptography

– SHA (SHA1, SHA224, SHA256, SHA384, SHA512): compliant with FIPS PUB 180-2

– AES: 256-, 192-, 128-bit key algorithm, compliant with FIPS PUB 197

– TDES: two-key or three-key algorithms, compliant with FIPS PUB 46-3

– True Random Number Generator (TRNG) compliant with NIST Special Publication 800-22 Test Suite and

FIPS PUBs 140-2 and 140-3

• I/O Ports

– Four 32-bit Parallel Input/Output Controllers

– Up to 112 programmable I/O Lines multiplexed with up to three peripheral I/Os

– Input change interrupt capability on each I/O line, optional Schmitt trigger input

– Individually programmable open-drain, pull-up and pull-down resistor, synchronous output

– General-purpose analog and digital inputs tolerant to positive and negative current injection

• Package

– DDR2-SDRAM variant: 233-ball BGA, 14x14 mm², 0.8 mm pitch, optimized for standard class PCB layout

(down to 2 layers)

– SDR-SDRAM variant: 196-ball BGA, 11x11 mm², 0.65 mm pitch, optimized for standard class PCB layout

(down to 4 layers)

• Design for Low Electromagnetic Interference (EMI)

– Slew rate controlled I/Os

– DDR/SDR Phy with impedance-calibrated drivers

– Spread spectrum PLLs

– Careful BGA power/ground ball assignment to provide optimum decoupling capacitors placement

• Operating Conditions

– Ambient temperature range (TA): -40°C to +85°C

– Junction temperature range (TJ) : -40°C to +125°C