首页>PN7362AUHN>规格书详情

PN7362AUHN中文资料数据手册PDF规格书

PN7362AUHN
厂商型号

PN7362AUHN

功能描述

NFC Cortex-M0 microcontroller

文件大小

746.43 Kbytes

页面数量

80

生产厂商 恩XP
原厂标识

恩XP

数据手册

下载地址一下载地址二到原厂下载

更新时间

2025-8-2 8:24:00

人工找货

PN7362AUHN价格和库存,欢迎联系客服免费人工找货

PN7362AUHN规格书详情

description

The PN736X family is a family of 32-bit ARM Cortex-M0-based NFC microcontrollers

offering high performance and low power consumption. It has a simple instruction set and

memory addressing along with a reduced code size compared to existing architectures.

PN736Xoffers an all in one solution, with features such as NFC, microcontroller, and

software in a single chip. It operates at CPU frequencies of up to 20 MHz. It is part of the

PN7462AU product family which offers a common set of features, library and tools.

The peripheral complement of the PN736X microcontroller includes 160/80 kB of flash

memory, 12 kB of SRAM data memory and 4 kB EEPROM. It also includes one host

interface with either high-speed mode I2C-bus, SPI, USB or high-speed UART, and two

master interfaces, SPI and Fast-mode Plus I2C-bus. Four general-purpose counter/

timers, a random number generator, one CRC coprocessor and up to 21 general-purpose

I/O pins are also available.

The PN736X NFC microcontroller offer a one chip solution to build contactless

applications. It is equipped with a highly integrated high-power output NFC-IC for

contactless communication at 13.56 MHz enabling EMV-compliance on RF level, without

additional external active components.

PN736X supports the following operating modes:

• ISO/IEC 14443-A and B, MIFARE

• JIS X 6319-4 (comparable with FeliCa scheme)

• ISO/IEC 15693, ICODE, ISO/IEC 18000-3 mode 3

• NFC protocols - tag reader/writer, P2P

• ISO/IEC 14443- type A card emulation

• EMVCo compliance

特性 Features

Integrated contactless interface frontend

• High RF output power frontend IC for transfer speed up to 848 kbit/s

• NFC IP1 and NFC IP2 support

• Full NFC tag support (type 1, type 2, type 3, type 4A and type 4B)

• P2P active and passive, target and initiator

• Card emulation ISO14443 type A

• ISO/IEC 14443 type A and type B

• MIFARE classic card

• ISO/IEC 15693, and ISO/IEC 18000-3 mode 3

• Low-power card detection

• Dynamic Power Control (DPC) support

• Compliance with EMV contactless protocol specification

• Compliance with NFC standards

Cortex-M0 microcontroller

• Processor core

– ARM Cortex: 32-bit M0 processor

– Built-in Nested Vectored Interrupt Controller (NVIC)

– Non-maskable interrupt

– 24-bit system tick timer

– Running frequency of up to 20 MHz

– Clock management to enable low power consumption

• Memory

– Flash: 160 (PN7362) / 80 kB (PN7360)

– SRAM: 12 kB

– EEPROM: 4 kB

– 40 kB boot ROM included, including USB mass storage primary boot loader for code

download

• Debug option

– Serial Wire Debug (SWD) interface

• Peripherals

– Host interface:

– USB 2.0 full speed with USB 3.0 hub connection capability

– HSUART for serial communication, supporting standards speeds from 9600 bauds to

115200 bauds, and faster speed up to 1.288 Mbit/s

– SPI with half-duplex and full duplex capability with speeds up to 7 Mbit/s

– I2C supporting standard mode, fast mode and high-speed mode with multiple address

support

– Master interface:

– SPI with half-duplex capability from 1 Mbit/s to 6.78 Mbit/s

– I2C supporting standard mode, fast mode, fast mode plus and clock stretching

• Up to 21 General-Purpose I/O (GPIO) with configurable pull-up/pull-down resistors

• GPIO1 to GPIO12 can be used as edge and level sensitive interrupt sources

• Power

– Two reduced power modes: standby mode and hard power-down mode

– Supports suspend mode for USB host interface

– Processor wake-up from hard power-down mode, standby mode, suspend mode via

host interface, GPIOs, RF field detection

– Integrated PMU to adjust internal regulators automatically, to minimize the power

consumption during all possible power modes

– Power-on reset

– RF supply: external, or using an integrated LDO (TX LDO, configurable with 3 V, 3.3

V, 3.6 V, 4.5 V, and 4.75 V)

– Pad voltage supply: external 3.3 V or 1.8 V, or using an integrated LDO (3.3 V

supply)

• Timers

– Four general-purpose timers

– Programmable Watchdog Timer (WDT)

• CRC coprocessor

• Random number generator

• Clocks

– Crystal oscillator at 27.12 MHz

– Dedicated PLL at 48 MHz for the USB

– Integrated HFO 20 MHz and LFO 365 kHz

• General

– HVQFN64 package

– Temperature range: -40 °C to +85 °C

Applications

• Physical access control

• Gaming

• USB NFC reader, including dual interface smart card readers

• Home banking, payment readers EMVCo compliant

• High integration devices

• NFC applications

供应商 型号 品牌 批号 封装 库存 备注 价格
恩XP
2022+
原厂原包装
8600
全新原装 支持表配单 中国著名电子元器件独立分销
询价
恩XP
2021/2022+
N/A
6000
原厂原装现货订货价格优势终端BOM表可配单提供样品
询价
恩XP
23+
HVQFN-64(9x9)
7087
NXP原厂渠道,2小时快速发货,大量现货库存
询价
恩XP
21+
QFN
1436
原装现货假一赔十
询价
恩XP
25+
N/A
6000
原装,请咨询
询价
恩XP
24+
NA/
8735
原厂直销,现货供应,账期支持!
询价
恩XP
24+
标准封装
7753
全新原装正品/价格优惠/质量保障
询价
恩XP
25+
HVQFN64
54687
百分百原装现货 实单必成 欢迎询价
询价
恩XP
23+
9865
原装正品,假一赔十
询价
恩XP
23+
NA
20094
正纳10年以上分销经验原装进口正品做服务做口碑有支持
询价