PCA9555HF

16-bit I2C-bus and SMBus I/O port with interrupt; • Operating power supply voltage range of 2.3 V to 5.5 V\n• 5 V tolerant I/Os\n• Polarity Inversion register\n• Active LOW interrupt output\n• Low standby current\n• Noise filter on SCL/SDA inputs\n• No glitch on power-up\n• Internal power-on reset\n• 16 I/O pins which default to 16 inputs\n• 0 Hz to 400 kHz clock frequency\n• ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101\n• Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\n• Five packages offered: SO24, SSOP24, TSSOP24, HVQFN24 and HWQFN24\n;

The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallel Input/Output (GPIO) expansion for I²C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.\nThe PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Output and Polarity Inversion (active HIGH or active LOW operation) registers. The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each Input or Output is kept in the corresponding Input or Output register. The polarity of the read register can be inverted with the Polarity Inversion register. All registers can be read by the system master. Although pin-to-pin and I2C-bus address compatible with the PCF8575, software changes are required due to the enhancements, and are discussed in Application Note AN469.\nThe PCA9555 open-drain interrupt output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed. The power-on reset sets the registers to their default values and initializes the device state machine.\nThree hardware pins (A0, A1, A2) vary the fixed I²C-bus address and allow up to eight devices to share the same I2C-bus/SMBus. The fixed I²C-bus address of the PCA9555 is the same as the PCA9554, allowing up to eight of these devices in any combination to share the same I2C-bus/SMBus.\n

恩XP

PCA9555HF

16-bit I2C-bus and SMBus I/O port with interrupt

Generaldescription ThePCA9555isa24-pinCMOSdevicethatprovides16bitsofGeneralPurposeparallelInput/Output(GPIO)expansionforI2C-bus/SMBusapplicationsandwasdevelopedtoenhancetheNXPSemiconductorsfamilyofI2C-busI/Oexpanders.Theimprovementsincludehigherdrivecapab

ETC

PCA9555HF

16-bit I2C-bus and SMBus I/O port with interrupt

ETC

PCA9555HF

16-bit I2C-bus and SMBus I/O port with interrupt

ETC

PCA9555N

16-bitI2C-busandSMBusI/Oportwithinterrupt

ETC

PCA9555N

SMBusI/OExpanderWithInterruptOutput

PCA9555N

16-bitI2C-busandSMBusI/Oportwithinterrupt

ETC

PCA9555N

16-bitI2CandSMBusI/Oportwithinterrupt

DESCRIPTION ThePCA9555isa24-pinCMOSdevicethatprovide16bitsofGeneralPurposeparallelInput/Output(GPIO)expansionforI2C/SMBusapplicationsandwasdevelopedtoenhancethePhilipsfamilyofICI/Oexpanders.Theimprovementsincludehigherdrivecapability,5VI/Otolerance,low

PHI

PCA9555N

16-bitI2C-busandSMBusI/Oportwithinterrupt

Generaldescription ThePCA9555isa24-pinCMOSdevicethatprovides16bitsofGeneralPurposeparallelInput/Output(GPIO)expansionforI2C-bus/SMBusapplicationsandwasdevelopedtoenhancetheNXPSemiconductorsfamilyofI2C-busI/Oexpanders.Theimprovementsincludehigherdrivecapab

ETC

PCA9555PW

SMBusI/OExpanderWithInterruptOutput