PCA9509PDP

Low power level translating I2C-bus/SMBus repeater; Bidirectional buffer isolates capacitance and allows 400 pF on port B of the device\nVoltage level translation from port A (0.8 V to 1.5 V) to port B (2.3 V to 5.5 V)\nNo internal current source on A port to reduce current consumption for portableapplications\nActive HIGH enable input disables current mirrors to reduce standby power\nOpen-drain inputs/outputs\nLock-up free operation\nSupports arbitration and clock stretching across the repeater\nAccommodates Standard-mode and Fast-mode I²C-bus devices and multiple masters\nPowered-off high-impedance I²C-bus pins\nOperating supply voltage range of 0.8 V to 1.5 V on port A, 2.3 V to 5.5 V on port B\nAll pins are 5 V tolerant with respect to ground pin\n0 Hz to 400 kHz clock frequency\nRemark: The maximum system operating frequency may be less than 400 kHzbecause of the delays added by the repeater.\nESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM perJESD22-C101\nLatch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\nPackages offered: TSSOP8, XQFN8\n;

The PCA9509P is a level translating I²C-bus/SMBus repeater with two voltage suppliesthat enables processor low voltage 2-wire serial bus to interface with standard I²C-bus orSMBus I/O. While retaining all the operating modes and features of the I²C-bus systemduring the level shifts, it also permits extension of the I²C-bus by providing bidirectionalbuffering for both the data (SDA) and the clock (SCL) lines, thus enabling the I²C-bus orSMBus maximum capacitance of 400 pF on the higher voltage side. Port A allows avoltage range from 0.8 V to 1.5 V and is overvoltage tolerant. Port B allows a voltagerange from 2.3 V to 5.5 V and is overvoltage tolerant. Both port A and port B SDA andSCL pins are high-impedance when the PCA9509P is unpowered.\nThe bus port B drivers are compliant with SMBus I/O levels, while port A uses an offsetLOW which prevents bus lock-up and allows the bidirectional nature of the device. Theoutput pull-down on the port A internal buffer LOW is set for approximately 0.2 VCC(A),while the input threshold of the internal buffer is set about 0.1 VCC(A) lower than that of theoutput voltage LOW. When the port A I/O is driven LOW internally, the LOW is notrecognized as a LOW by the input. This prevents a lock-up condition from occurring. Theoutput pull-down on the port B drives a hard LOW and the input level is set at 0.3 ofSMBus or I²C-bus voltage level which enables port B to connect to any other I²C-busdevices or buffer.\nThe PCA9509P drivers are not enabled unless VCC(A) is above 0.7 V and VCC(B) is above1.7 V. The enable (EN) pin can also be used to turn the drivers on and off under systemcontrol. Caution should be observed to only change the state of the EN pin when the busis idle.\nThe PCA9509P is the same as the PCA9509A but without the port A internal currentsource to allow high value pull-up resistors to reduce current consumption in portableapplications.\nSelection recommendationsThe PCA9509P should be used if an external A-port pull-up resistor is required to adjustcurrent for noise margin considerations or to reduce operating current consumption.\nTable 1. Device selection recommendationConcern\nRecommended device\nPCA9509\nPCA9509A\nPCA9509P\nA-port — lowest voltage\n1.0 V\n0.85 V\n0.85 V\nA-port — current source [1]\nyes—1 mA\nyes—270 μA\nno—external pull-up\noperating current [2]\n< 6.1 mA\n< 1.9 mA\n< 0.95 mA\nstandby current EN = LOW\n< 2 mA\n< 22 μA max.\n< 22 μA max.\nThe PCA9509 current mirrors do not shut down when the device is disabled allowing instant turn-on, but atthe cost of the higher standby current. The PCA9509A and PCA9509P current mirrors are turned off whendisabled for lowest standby power consumption, but sufficient delay (10 μs) after enable is needed beforeresuming operation.\nOperating currents do not include the current consumed by the external pull-ups on B-port or the externalpull-ups on the A-port of the PCA9509P.\n

PCA9509PGM

Low power level translating I2C-bus/SMBus repeater; Bidirectional buffer isolates capacitance and allows 400 pF on port B of the device\nVoltage level translation from port A (0.8 V to 1.5 V) to port B (2.3 V to 5.5 V)\nNo internal current source on A port to reduce current consumption for portableapplications\nActive HIGH enable input disables current mirrors to reduce standby power\nOpen-drain inputs/outputs\nLock-up free operation\nSupports arbitration and clock stretching across the repeater\nAccommodates Standard-mode and Fast-mode I²C-bus devices and multiple masters\nPowered-off high-impedance I²C-bus pins\nOperating supply voltage range of 0.8 V to 1.5 V on port A, 2.3 V to 5.5 V on port B\nAll pins are 5 V tolerant with respect to ground pin\n0 Hz to 400 kHz clock frequency\nRemark: The maximum system operating frequency may be less than 400 kHzbecause of the delays added by the repeater.\nESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM perJESD22-C101\nLatch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA\nPackages offered: TSSOP8, XQFN8\n;

The PCA9509P is a level translating I²C-bus/SMBus repeater with two voltage suppliesthat enables processor low voltage 2-wire serial bus to interface with standard I²C-bus orSMBus I/O. While retaining all the operating modes and features of the I²C-bus systemduring the level shifts, it also permits extension of the I²C-bus by providing bidirectionalbuffering for both the data (SDA) and the clock (SCL) lines, thus enabling the I²C-bus orSMBus maximum capacitance of 400 pF on the higher voltage side. Port A allows avoltage range from 0.8 V to 1.5 V and is overvoltage tolerant. Port B allows a voltagerange from 2.3 V to 5.5 V and is overvoltage tolerant. Both port A and port B SDA andSCL pins are high-impedance when the PCA9509P is unpowered.\nThe bus port B drivers are compliant with SMBus I/O levels, while port A uses an offsetLOW which prevents bus lock-up and allows the bidirectional nature of the device. Theoutput pull-down on the port A internal buffer LOW is set for approximately 0.2 VCC(A),while the input threshold of the internal buffer is set about 0.1 VCC(A) lower than that of theoutput voltage LOW. When the port A I/O is driven LOW internally, the LOW is notrecognized as a LOW by the input. This prevents a lock-up condition from occurring. Theoutput pull-down on the port B drives a hard LOW and the input level is set at 0.3 ofSMBus or I²C-bus voltage level which enables port B to connect to any other I²C-busdevices or buffer.\nThe PCA9509P drivers are not enabled unless VCC(A) is above 0.7 V and VCC(B) is above1.7 V. The enable (EN) pin can also be used to turn the drivers on and off under systemcontrol. Caution should be observed to only change the state of the EN pin when the busis idle.\nThe PCA9509P is the same as the PCA9509A but without the port A internal currentsource to allow high value pull-up resistors to reduce current consumption in portableapplications.\nSelection recommendationsThe PCA9509P should be used if an external A-port pull-up resistor is required to adjustcurrent for noise margin considerations or to reduce operating current consumption.\nTable 1. Device selection recommendationConcern\nRecommended device\nPCA9509\nPCA9509A\nPCA9509P\nA-port — lowest voltage\n1.0 V\n0.85 V\n0.85 V\nA-port — current source [1]\nyes—1 mA\nyes—270 μA\nno—external pull-up\noperating current [2]\n< 6.1 mA\n< 1.9 mA\n< 0.95 mA\nstandby current EN = LOW\n< 2 mA\n< 22 μA max.\n< 22 μA max.\nThe PCA9509 current mirrors do not shut down when the device is disabled allowing instant turn-on, but atthe cost of the higher standby current. The PCA9509A and PCA9509P current mirrors are turned off whendisabled for lowest standby power consumption, but sufficient delay (10 μs) after enable is needed beforeresuming operation.\nOperating currents do not include the current consumed by the external pull-ups on B-port or the externalpull-ups on the A-port of the PCA9509P.\n

PE9509

Precision7/16DINMaleto7mmSexlessAdapter

PL9509

SMTPOWERINDUCTORS

TCA9509

TCA9509Level-TranslatingI2CandSMBUSBusRepeater

TCA9509

LEVEL-TRANSLATINGI2C/SMBUSBUSREPEATER

TCA9509DGKR

LEVEL-TRANSLATINGI2C/SMBUSBUSREPEATER

TCA9509DGKR

TCA9509Level-TranslatingI2CandSMBUSBusRepeater

TCA9509MRVHR

TCA9509Level-TranslatingI2CandSMBUSBusRepeater

TCA9509RVHR

LEVEL-TRANSLATINGI2C/SMBUSBUSREPEATER