Low-voltage analog switch

General description The NX3V1T66 provides one single-pole single-throw analog switch function. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit

文件：125.29 Kbytes 页数：18 Pages

恩XP

Low-ohmic single-pole single-throw analog switch

文件：456.24 Kbytes 页数：20 Pages

恩XP

低电阻单刀单掷模拟开关

NX3V1T66是低电阻单刀单掷模拟开关。其具有两个输入/输出端子（Y和Z）和有源高电平使能输入引脚(E)。引脚E为低电平时，模拟开关关闭。\n施密特触发器在使能输入(E)处工作，这使得电路容许较慢的输入上升和下降时间。低输入电压阈值允许引脚E由低电平逻辑信号驱动，而没有显著增加电源电流ICC。这使NX3V1T66能够通过1.8 V的数字控制器切换4.3 V的信号，无需逻辑电平转换。\nNX3V1T66允许具有高达VCC振幅的信号从Y传输到Z；或从Z传输到Y。其超低导通电阻(0.3 Ω)和平坦度(0.1 Ω)确保传输的信号具有最小衰减和失真。 宽电源电压范围从1.4 V至4.3 V\n极低的导通电阻（峰值）： VCC = 1.4 V时为0.8 Ω（典型值）\nVCC = 1.65 V时为0.5 Ω（典型值）\nVCC = 2.3 V时为0.3 Ω（典型值）\nVCC = 2.7 V时为0.25 Ω（典型值）\nVCC = 4.3 V时为0.25 Ω（典型值）\n\n高抗噪性\nESD保护： HBM JESD22–A114F 3A类超过7500 V\nMM JESD22–A115–A超过200 V\nCDM AEC–Q100–011修订版B超过1000 V\n开关端口的IEC61000-4-2接触放电超过6000 V\n\n低功耗CM;

恩XP

Low-voltage analog switch

General description The NX3V1T66 provides one single-pole single-throw analog switch function. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit

文件：125.29 Kbytes 页数：18 Pages

恩XP

Low-voltage analog switch

General description The NX3V1T66 provides one single-pole single-throw analog switch function. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned off. Schmitt trigger action at the enable input (E) makes the circuit

文件：125.29 Kbytes 页数：18 Pages

恩XP

Low-ohmic single-pole single-throw analog switch

文件：456.24 Kbytes 页数：20 Pages

恩XP

Low-ohmic single-pole single-throw analog switch

文件：189.49 Kbytes 页数：20 Pages

PHI

PHI

Low-ohmic single-pole single-throw analog switch

文件：456.24 Kbytes 页数：20 Pages

恩XP

Low-ohmic single-pole single-throw analog switch

文件：456.24 Kbytes 页数：20 Pages

恩XP

低电阻单刀单掷模拟开关

NX3V1T66是低电阻单刀单掷模拟开关。其具有两个输入/输出端子（Y和Z）和有源高电平使能输入引脚(E)。引脚E为低电平时，模拟开关关闭。\n施密特触发器在使能输入(E)处工作，这使得电路容许较慢的输入上升和下降时间。低输入电压阈值允许引脚E由低电平逻辑信号驱动，而没有显著增加电源电流ICC。这使NX3V1T66能够通过1.8 V的数字控制器切换4.3 V的信号，无需逻辑电平转换。\nNX3V1T66允许具有高达VCC振幅的信号从Y传输到Z；或从Z传输到Y。其超低导通电阻(0.3 Ω)和平坦度(0.1 Ω)确保传输的信号具有最小衰减和失真。 宽电源电压范围从1.4 V至4.3 V\n极低的导通电阻（峰值）： VCC = 1.4 V时为0.8 Ω（典型值）\nVCC = 1.65 V时为0.5 Ω（典型值）\nVCC = 2.3 V时为0.3 Ω（典型值）\nVCC = 2.7 V时为0.25 Ω（典型值）\nVCC = 4.3 V时为0.25 Ω（典型值）\n\n高抗噪性\nESD保护： HBM JESD22–A114F 3A类超过7500 V\nMM JESD22–A115–A超过200 V\nCDM AEC–Q100–011修订版B超过1000 V\n开关端口的IEC61000-4-2接触放电超过6000 V\n\n低功耗CM;

恩XP