NX3V1G66

低电阻单刀单掷模拟开关; 宽电源电压范围从1.4 V至4.3 V\n极低的导通电阻（峰值）： VCC = 1.4 V时为0.8 Ω（典型值）\nVCC = 1.65 V时为0.5 Ω（典型值）\nVCC = 2.3 V时为0.3 Ω（典型值）\nVCC = 2.7 V时为0.25 Ω（典型值）\nVCC = 4.3 V时为0.25 Ω（典型值）\n\n高抗噪性\nESD保护： HBM JESD22– A114F 3A类超过7500 V\nMM JESD22– A115– A超过200 V\nCDM AEC– Q100– 011修订版B超过1000 V\n\n低功耗CMOS\n闭锁性能超过JESD78B II类A级规定的100 mA\n3.0 V TTL电平的直接接口\n控制输入接受高于电源电压的电压\n高电流处理能力（3.3 V供电时500 mA的连续电流）\n额定温度范围为-40 °C至+85 °C和-40 °C至+125 °C\n;

NX3V1G66提供一个单刀单掷模拟开关功能。其具有两个输入/输出端子（Y和Z）和有源高电平使能输入引脚(E)。引脚E为低电平时，模拟开关关闭。\n施密特触发器在使能输入(E)处工作，这使得电路在从1.4 V至4.3 V的整个VCC范围内容许较慢的输入上升和下降时间。\nNX3V1G66允许具有高达VCC振幅的信号从Y传输到Z；或从Z传输到Y。其超低导通电阻(0.3 Ω)和平坦度(0.1 Ω)确保传输的信号具有最小衰减和失真。\n

NX3V1G66GM

低电阻单刀单掷模拟开关; 宽电源电压范围从1.4 V至4.3 V\n极低的导通电阻（峰值）： VCC = 1.4 V时为0.8 Ω（典型值）\nVCC = 1.65 V时为0.5 Ω（典型值）\nVCC = 2.3 V时为0.3 Ω（典型值）\nVCC = 2.7 V时为0.25 Ω（典型值）\nVCC = 4.3 V时为0.25 Ω（典型值）\n\n高抗噪性\nESD保护： HBM JESD22– A114F 3A类超过7500 V\nMM JESD22– A115– A超过200 V\nCDM AEC– Q100– 011修订版B超过1000 V\n\n低功耗CMOS\n闭锁性能超过JESD78B II类A级规定的100 mA\n3.0 V TTL电平的直接接口\n控制输入接受高于电源电压的电压\n高电流处理能力（3.3 V供电时500 mA的连续电流）\n额定温度范围为-40 °C至+85 °C和-40 °C至+125 °C\n;

NX3V1G66提供一个单刀单掷模拟开关功能。其具有两个输入/输出端子（Y和Z）和有源高电平使能输入引脚(E)。引脚E为低电平时，模拟开关关闭。\n施密特触发器在使能输入(E)处工作，这使得电路在从1.4 V至4.3 V的整个VCC范围内容许较慢的输入上升和下降时间。\nNX3V1G66允许具有高达VCC振幅的信号从Y传输到Z；或从Z传输到Y。其超低导通电阻(0.3 Ω)和平坦度(0.1 Ω)确保传输的信号具有最小衰减和失真。\n

NX3V1G66GW

低电阻单刀单掷模拟开关; Wide supply voltage range from 1.4 V to 4.3 V\nVery low ON resistance (peak): 0.8 Ω (typical) at VCC = 1.4 V\n0.5 Ω (typical) at VCC = 1.65 V\n0.3 Ω (typical) at VCC = 2.3 V\n0.25 Ω (typical) at VCC = 2.7 V\n0.25 Ω (typical) at VCC = 4.3 V\nHigh noise immunity\nESD protection: HBM JESD22– A114F Class 3A exceeds 7500 V\nMM JESD22– A115– A exceeds 200 V\nCDM AEC– Q100– 011 revision B exceeds 1000 V\nCMOS low– power consumption\nLatch– up performance exceeds 100 mA per JESD78B Class II Level A\nDirect interface with TTL levels at 3.0 V\nControl input accepts voltages above supply voltage\nHigh current handling capability (500 mA continuous current under 3.3 V supply)\nSpecified from – 40 °C to +85 °C and from – 40 °C to +125 °C\n;

The NX3V1G66 provides one single–pole single–throw analog switch function. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When pin E is LOW, the analog switch is turned off.\nSchmitt trigger action at the enable input (E) makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 1.4 V to 4.3 V.\nThe NX3V1G66 allows signals with amplitude up to VCC to be transmitted from Y to Z or from Z to Y. Its ultra–low ON resistance (0.3 Ω) and flatness (0.1 Ω) ensures minimal attenuation and distortion of transmitted signals.\n