MIC3003GFL中文资料High Speed Communication Fiber Optic Module Controller Products数据手册Microchip规格书

描述 Description

The MIC3003GFL is a fiber optic module controller which enables the implementation of sophisticated, hot-pluggable fiber optic transceivers with intelligent laser control and an internally calibrated Digital Diagnostic Monitoring Interface per SFF-8472. It essentially integrates all non-data path functions of an SFP/SFP+ transceiver into a tiny ( 3mm x 3mm) MLF® package. It also works well as a microcontroller peripheral in transponders or 10Gbps transceivers. The MIC3003GFL uses the same die as the MIC3003 with all its functions, but in a smaller package and different pin out.A highly configurable automatic power control (APC) circuit controls laser bias. Bias and modulation are temperature compensated using dual DACs, an on-chip temperature sensor, and NVRAM look-up tables. A programmable internal feedback resistor provides a wide dynamic range for the APC. Controlled laser turn-on.An analog-to-digital converter converts the measured temperature, voltage, bias current, transmit power, and received power from analog to digital. An EEPOT provides front-end adjustment of RX power. Each parameter is compared against user-programmed warning and alarm thresholds. Analog comparators and DACs provide fast monitoring of received power and critical laser operating parameters. Data can be reported as either internally calibrated or externally calibrated.An interrupt output, power-on hour meter, and data-ready bits add user friendliness beyond SFF-8472. The interrupt output and data-ready bits reduce overhead in the host system. The power-on hour meter logs operating hours using an internal real-time clock and stores the result in NVRAM.In addition to the features listed above, the MIC3003 features an extended temperature range, options to mask alarms and warnings interrupt and TXFAULT, a reset signal source, and the ability to support up to four chips with the same address on the serial interface. It also supports eight-byte SMBus block writes.Communication with the MIC3003 is via an industry standard 2-wire SMBus serial interface. Nonvolatile memory is provided for serial ID, configuration, and separate OEM and user scratchpad spaces.

特性 Features

• Packaged in a ultra small (3mm x 3mm) 24-pin MLF® package
• Extended temperature range
• Alarms and warnings interrupt and TXFAULT masks
• Capability to support up to four devices on one SMBus
• APC or constant-current laser bias
• Turbo mode for APC loop start-up and shorter laser turn on time
• Supports multiple laser types and bias circuit topologies
• Integrated digital temperature sensor
• Temperature compensation of modulation, bias, bias fault and alarm thresholds via NVRAM look-up tables
• NVRAM to support GBIC/SFP serial ID function
• User writable EEPROM scratchpad
• Reset signal compatible with some new systems requirements
• Diagnostic monitoring interface per SFF-8472
• Monitors and reports critical parameters: temperature, bias current, TX and RX optical power, and supply voltage
• S/W control and monitoring of TXFAULT, RXLOS, RATESELECT, and TXDISABLE
• Internal or external calibration
• EEPOT for adjusting RX power measurement
• Power-on hour meter
• Interrupt capability
• Extensive test and calibration features
• 2-wire SMBus-compatible serial interface

简介

MIC3003GFL属于集成电路（IC）的激光驱动器。由Microchip制造生产的MIC3003GFL激光驱动器激光驱动器电源管理集成电路 (PMIC) 可用于提供一个或多个受控电流源，以从标称恒定电压电源为半导体激光器件供电。产品通常支持通过监控受驱动的激光器件发出的光功率而得到反馈，可广泛应用于光通信系统中；并因具有对提供给用电设备的电流进行高频调制的能力，而与执行类似功能的器件区分开来。