MB86606A数据手册Fujitsu中文资料规格书

描述 Description

■DESCRIPTION
The MB86606A is an intelligent SCSI protocol controller (SPC) conforming to the ANSI (FAST-20) standard and integrating a PCI local bus interface function. The specification of SCSI controller block is based on the MB86605’s one which is a Wide SCSI protocol controller, but the device functions/features to achieve the FAST-20 data transfer rate of maximum 40 Mbyte/sec at 16-bit FAST-20 SCSI, such as the size of internal data register FIFO, are larged on the MB86606A. As for the SCSI bus pins, a totem pole type single-ended driver/receiver is incorporated in the device so that it can drive the SCSI bus directly. Furthermore, the MB86606A is capable of connecting the external differential type driver/receiver.■FEATURES
SCSI Protocol Controller Block:

• Operable as initiator and target
• WIDE and FAST-20 data transfers
   Synchronous transfer (max. 40 Mbytes/s: Up to 256 offset values can be set.)
   Asynchronous transfer (max. 10 Mbytes/s)
• 512-byte FIFO register for data phase
• Two types (send-only and receive-only) of 32-byte data buffers for message, command, and status phases (MCS Buffers)
• On-chip totem pole type SCSI single-ended driver/receiver
• Supports external SCSI differential driver/receiver connectivity
• On-chip memory to store transfer parameters for each ID (up to 15 connected devices)
• On-chip 16-bit transfer block counter and 24-bit transfer byte counter
   Maximum Transfer Byte : 1 Tbyte at fixed length data transfer : 16 Mbyte at variable length data transfer
• Supports various control commands:
Sequential Commands : can perform phase-to-phase sequential operations (functions only when issuing from a system side.)
Discrete Commands : can perform any desired sequence to program in the user program memory
Data Transfer Commands : can program the transfer data length at the user program operation.
• On-chip direct control register for SCAM (SCSI Configured AutoMatically) Level-1 Protocol
• Supports Multi Selection/Reselection Responses
Selection and Reselection responses can be done to plural IDs.
• On-chip 2 Kbyte User Program Memory
Two Modes : 2 Kbyte ×1 bank and 1 Kbyte ×2 banks
(While 1 Kbyte ×2 banks are selected, host system can access another bank even if the user
program is executing.)
Access to User program : Burst transfer via I/O access port
: Direct access to 2 Kbyte user program memory (only for PCI bus I/F mode)
• User Selectable Interrupt Report
Unnecessary interrupt reports can be disabled depending on user’s applications to reduce a system ISR
overhead.
• Two automatic receive modes
Initiator : can automatically receive information for new phase to which target switched
Target : can automatically receive attention condition generated by initiator
• Automatic selection/reselection
For command issues : automatically performs to receive MSG/CMD to the selection/reselection
request from partner device
For user program operation : pauses the program currently executed and automatically jumps to the
specified selection /reselection routine in response to the selection/reselection
request from partner device.
• Operation Clock
System Clock: Max. 40 MHz
Internal Processor Operating Clock: Max. 20 MHz

特性 Features

SCSI Protocol Controller Block:

• Operable as initiator and target
• WIDE and FAST-20 data transfers
   Synchronous transfer (max. 40 Mbytes/s: Up to 256 offset values can be set.)
   Asynchronous transfer (max. 10 Mbytes/s)
• 512-byte FIFO register for data phase
• Two types (send-only and receive-only) of 32-byte data buffers for message, command, and status phases (MCS Buffers)
• On-chip totem pole type SCSI single-ended driver/receiver
• Supports external SCSI differential driver/receiver connectivity
• On-chip memory to store transfer parameters for each ID (up to 15 connected devices)
• On-chip 16-bit transfer block counter and 24-bit transfer byte counter
   Maximum Transfer Byte : 1 Tbyte at fixed length data transfer : 16 Mbyte at variable length data transfer
• Supports various control commands:
Sequential Commands : can perform phase-to-phase sequential operations (functions only when issuing from a system side.)
Discrete Commands : can perform any desired sequence to program in the user program memory
Data Transfer Commands : can program the transfer data length at the user program operation.
• On-chip direct control register for SCAM (SCSI Configured AutoMatically) Level-1 Protocol
• Supports Multi Selection/Reselection Responses
Selection and Reselection responses can be done to plural IDs.
• On-chip 2 Kbyte User Program Memory
Two Modes : 2 Kbyte ×1 bank and 1 Kbyte ×2 banks
(While 1 Kbyte ×2 banks are selected, host system can access another bank even if the user
program is executing.)
Access to User program : Burst transfer via I/O access port
: Direct access to 2 Kbyte user program memory (only for PCI bus I/F mode)
• User Selectable Interrupt Report
Unnecessary interrupt reports can be disabled depending on user’s applications to reduce a system ISR
overhead.
• Two automatic receive modes
Initiator : can automatically receive information for new phase to which target switched
Target : can automatically receive attention condition generated by initiator
• Automatic selection/reselection
For command issues : automatically performs to receive MSG/CMD to the selection/reselection
request from partner device
For user program operation : pauses the program currently executed and automatically jumps to the
specified selection /reselection routine in response to the selection/reselection
request from partner device.
• Operation Clock
System Clock: Max. 40 MHz
Internal Processor Operating Clock: Max. 20 MHz