MAX3243E中文资料具有 +/-15kV IEC-ESD 保护的 3V 至 5.5V 多通道 500kbps RS-232 线路驱动器/接收器数据手册TI规格书

描述 Description

The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with ±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, ContactDischarge) protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-portconnector. This combination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, or compatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, the device includes an always-active noninverting output (ROUT2B), which allows applicationsusing the ring indicator to transmit data while the device is powered down. The device operates at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate.

Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low, both drivers and receivers (except ROUT2B) are shut off, and the supply current is reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown condition to occur.

Auto-powerdown can be disabled when FORCEON and FORCEOFF are high, and should be done when driving a serial mouse. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7 V or has been between –0.3 V and 0.3 V for less than30 µs. INVALID is low (invalid data) if all receiver input voltages are between –0.3 V and 0.3 V for more than 30 µs. Refer to Figure 5 for receiver input levels.

The MAX3243EC is characterized for operation from 0°C to 70°C. The MAX3243EI is characterized for operation from –40°C to 85°C.

特性 Features

• Single-Chip and Single-Supply Interface for IBM PC/AT Serial Port
• ESD Protection for RS-232 Bus Pins
• ±15-kV Human-Body Model (HBM)
• ±8-kV IEC61000-4-2, Contact Discharge
• ±15-kV IEC61000-4-2, Air-Gap Discharge

• Meets or Exceeds Requirements of TIA/EIA-232-F and ITU v.28 Standards
• Operates With 3-V to 5.5-V VCC Supply
• Always-Active Noninverting Receiver Output (ROUT2B)
• Designed to Transmit at a Data Rate up to500 kbit/s
• Low Standby Current . . . 1 µA Typ
• External Capacitors . . . 4 × 0.1 µF
• Accepts 5-V Logic Input With 3.3-V Supply
• Designed to Be Interchangeable With Maxim MAX3243E
• Serial-Mouse Driveability
• Auto-Powerdown Feature to Disable Driver Outputs When No Valid RS-232 Signal Is Sensed
• Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages

简介

MAX3243E属于集成电路（IC）的驱动器接收器收发器。由TI制造生产的MAX3243E驱动器，接收器，收发器该系列产品的主要功能是提供必需的硬件资源，以通过延长电缆或印制线进行通信。确切的功能会因所采用的通信协议而异，可能包括诸如瞬态抑制之类的功能，这些功能对于通信用途可能并非绝对必要，但对于可能的使用环境却是明智之选。