LPC4330FET180中文资料双核Cortex-M4/M0、264 KB SRAM、2个带片上PHY的高速USB、以太网、CAN、AES、SPIFI、SGPIO、SCT数据手册恩XP规格书

描述 Description

The LPC4330FET180 is an Arm® Cortex®-M4 based digital signal controller with an Arm Cortex-M0 coprocessor designed for embedded applications requiring signal processing. The Arm Cortex-M4 core offers single-cycle Multiply-Accumulate and SIMD instructions and a hardware floating-point unit to support signal processing while the M0 coprocessor handles I/O and digital control processing. The LPC4330FET180 includes 264 kB of data memory, two High Speed USB 2.0 Host/OTG/Devices, advanced configurable peripherals such as the State Configurable Timer (SCT), Serial General Purpose I/O (SGPIO), and SPI Flash Interface (SPIFI) as well as Ethernet, an external memory controller and multiple digital and analog peripherals.

特性 Features

• Arm Cortex-M4 processor, running at frequencies of up to 204 MHz
• Arm Cortex-M4 built-in Memory Protection Unit (MPU) supporting eight regions
• Arm Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC)
• Hardware floating-point unit
• Non-maskable Interrupt (NMI) input
• JTAG and Serial Wire Debug (SWD)
• System tick timer
• Arm Cortex-M0 co-processor running at frequencies of up to 204 MHz
• 256 kB SRAM for code and data use
• Two 32 kB SRAM blocks with separate bus access
• 32 kB ROM containing boot code and on-chip software drivers
• 32 bit One-Time Programmable (OTP) memory for customer use
• Serial GPIO (SGPIO) interface
• State Configurable Timer (SCT) subsystem on AHB
• Quad SPI Flash Interface (SPIFI) with four lanes and up to 40 MB per second
• 10/100T Ethernet MAC with RMII and MII interfaces and DMA support
• One High-speed USB 2.0 Host/Device/OTG interface with DMA support
• One High-speed USB 2.0 Host/Device interface with DMA support
• One 550 UART with DMA support and full modem interface
• Three 550 USARTs with DMA and synchronous mode support
• One C_CAN 2.0B controller with one channel
• Two SSP controllers with FIFO and multi-protocol support
• One SPI controller
• One Fast-mode Plus I2C-bus interface with rates of up to 1 Mbit/s
• One Fast-mode I2C-bus interface
• Two I2S interfaces
• External Memory Controller (EMC) supporting external SRAM, ROM, flash, SDRAM
• Secure Digital Input Output (SDIO) card interface
• Eight-channel General-Purpose DMA (GPDMA) controller
• Up to 118 General-Purpose Input/Output (GPIO) pins
• Four general-purpose timer/counters with capture and match capabilities
• One motor control Pulse Width Modulator (PWM) for three-phase motor control
• One Quadrature Encoder Interface (QEI)
• Repetitive Interrupt timer (RI timer)
• Windowed watchdog timer (WWDT)
• Ultra-low power Real-Time Clock (RTC) on separate power domain
• Alarm timer; can be battery powered
• One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
• Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
• Two 128-bit secure OTP memories for AES key storage and customer use
• Crystal oscillator with an operating range of 1 MHz to 25 MHz
• 12 MHz Internal RC (IRC) oscillator trimmed to 1 % accuracy
• Ultra-low power Real-Time Clock (RTC) crystal oscillator
• Three PLLs allow CPU operation up to the maximum CPU rate
• Clock output
• Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip DC-to-DC converter
• RTC power domain can be powered separately by a 3 V battery supply
• Four reduced power modes
• Processor wake-up from Sleep mode via wake-up interrupts
• Brownout detect with four separate thresholds for interrupt and forced reset
• Power-On Reset (POR)
• see selection guide for features per type

应用 Application

工业
消费品
白色家电
RFID读取器
电子计量