LPC1830FET256中文资料0kB Flash、200kB SRAM、以太网、LBGA256封装数据手册恩XP规格书

描述 Description

The LPC1830FET256 is a high-performance, cost-effective Cortex-M3 microcontroller featuring 200 kB of SRAM, and advanced peripherals including Ethernet, High Speed USB 2.0 Host/OTG/Device and CAN 2.0B. Operating at speeds up to 180 MHz, the LPC1830 also features two new configurable peripherals: a SPI Flash Interface and a State Configurable Timer. All members of the series include a Wakeup Interrupt Controller allowing automatic wake from any priority interrupt as well as four reduced power modes: Sleep, Deep-Sleep, Power-Down, and Deep Power-Down.

特性 Features

• Arm Cortex-M3 processor, running at frequencies of up to 180 MHz
• Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions
• Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
• Non-maskable Interrupt (NMI) input
• JTAG and Serial Wire Debug
• ETM and ETB support
• System tick timer
• 200 kB SRAM for code and data use
• 32 kB ROM containing boot code and on-chip software drivers
• Crystal oscillator with an operating range of 1 MHz to 25 MHz
• 12 MHz internal RC oscillator trimmed to 1 % accuracy
• Ultra-low power RTC crystal oscillator
• Clock output
• Two PLLs allow CPU operation up to the maximum CPU rate
• Quad SPI Flash Interface with four lanes and data rates of up to 40 MB/s
• 10/100T Ethernet MAC with RMII and MII interfaces and DMA support
• One High-speed USB 2.0 Host/Device/OTG interface with DMA
• One High-speed USB 2.0 Host/Device interface with DMA support
• Four 550 UARTs with DMA support: one UART with full modem interface
• One UART with IrDA interface
• One C_CAN 2.0B controller with one channel
• Two SSP controllers with FIFO and multi-protocol support
• One Fast-mode Plus I2C-bus interface with monitor mode
• One standard I2C-bus interface with monitor mode and standard I/O pins
• One I2S interface with DMA support and with one input and one output
• External Memory Controller (EMC)
• SD/MMC card interface
• Eight-channel General-Purpose DMA (GPDMA) controller
• Up to 164 General-Purpose Input/Output (GPIO) pins
• GPIO registers are located on the AHB for fast access
• State Configurable Timer (SCT) subsystem on AHB
• Four general-purpose timer/counters with capture and match capabilities
• One motor control PWM for three-phase motor control
• One Quadrature Encoder Interface (QEI)
• Repetitive Interrupt timer (RI timer)
• Windowed watchdog timer
• Ultra-low power Real-Time Clock (RTC) on separate power domain
• Alarm timer; can be battery powered
• One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
• Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
• Hardware-based AES security engine programmable through an on-chip API
• Two 128-bit secure OTP memories for AES key storage and customer use
• Unique ID for each device
• Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip voltage regulator
• RTC power domain can be powered separately by a 3 V battery supply
• Four reduced power modes
• Overdrive mode to increase CPU and bus clock frequency
• Processor wake-up from Sleep mode via wake-up interrupts
• Wake-up from Deep-sleep, Power-down, and Deep power-down modes
• Brownout detect with four separate thresholds for interrupt and forced reset
• Power-On Reset (POR)

应用 Application

工业
消费电子
白色家电
RFID读卡器
电子计量