L6730数据手册集成电路（IC）的PMIC-稳压器-DCDC开关式控制器规格书PDF

描述 Description

The controller is an integrated circuit designed using BiCMOS-DMOS, v5 (BCD5) technology that provides complete control logic and protection for high performance, stepdown DC/DC and niPOL converters.
It is designed to drive N-Channel MOSFETs in a synchronous rectified buck converter topology. The output voltage of the converter can be precisely regulated down to 600 mV, with a maximum tolerance of ±0.8%, or to 1.2 V, when one of the internal references is used.
It is also possible to use an external reference from 0 V to 2.5 V.
The input voltage can range from 1.8 V to 14 V, while the supply voltage can range from 4.5 V to 14 V. High peak current gate drivers provide for fast switching to the external power section and the output current can be in excess of 20 A, depending on the number of the external MOSFETs used. The PWM duty cycle can range from 0% to 100% with a minimum on-time (TON(MIN)) lower than 100 ns, making conversions with a very low duty cycle and very high switching frequency possible.
The device provides voltage-mode control. It includes a 400 kHz free-running oscillator that is adjustable from 100 kHz to 1 MHz. The error amplifier features a 10 MHz gain-bandwidthproduct and 5 V/μs slew-rate that permits to realize high converter bandwidth for fast transient response. The device monitors the current by using the RDS(ON) of both the highside and low-side MOSFET(s), eliminating the need for a current sensing resistor and guaranteeing an effective over current-protection in all the application conditions. When necessary, two different current limit protections can be externally set through two external resistors. A leading edge adjustable blanking time is also available to avoid false overcurrent- protection (OCP) intervention in every application condition.
It is possible to select the HICCUP mode or the constant current protection (L6730B) after the soft-start phase.
During this phase constant current protection is provided. It is possible to select the sinksource or the source-only mode capability (before the device powers on) by acting on a multifunction pin (L6730). The L6730 disables the sink mode capability during the soft-start in order to allow a proper start-up also in pre-biased output voltage conditions. The L6730B can always sink current and, so it can be used to supply the DDR memory BUS termination.
Other features include Master-Slave synchronization (with 180° phase shift), Power-Good with adjustable delay, over voltage-protection, feed back disconnection, selectable UVLO threshold (5 V and 12 V Bus), and thermal shutdown. The HTSSOP20 package allows the realization for very compact DC/DC converters.

特性 Features

High current embedded drivers
Soft-start and inhibit
Selectable uvlo threshold (5 V or 12 V BUS)
Predictive anti-cross conduction control
Switching frequency programmable from 100 kHz to 1 MHz
Programmable high-side and low-side RDS(on) sense overcurrent protection
Pre-bias start up capability (L6730)
Master/slave synchronization with 180° phase shift
Selectable source/sink or source only capability after soft-start (L6730)
Power Good output with programmable delay
Selectable constant current or hiccup mode overcurrent protection after soft-start (L6730B)
Thermal shut-down
Overvoltage protection with selectable latched/not-latched mode
Package: HTSSOP20
Selectable 0.6 V or 1.2 V internal voltage reference
0% to 100% duty cycle
Input voltage range from 1.8 V to 14 V
Adjustable output voltage down to 0.6 V with ±0.8% accuracy over line voltage and temperature (0°C~125°C)
Supply voltage range from 4.5 V to 14 V
t
ON lower than 100 ns
External input voltage reference
Fixed frequency voltage mode control

简介

L6730属于集成电路（IC）的PMIC-稳压器-DCDC开关式控制器。由制造生产的L6730DC-DC 开关控制器PMIC（电源管理集成电路）DC 到 DC 开关式控制器是用于高效率电路的稳压 IC，其配置为生成高于（突升或步升）或低于（突降或步降）输入电源的输出电源电压。其他拓扑结构可能包括：降压-升压、反激、正激、Cuk、SEPIC、全桥、半桥和推挽式。这些器件不同于需要最小电压并“烧尽”多余电压的线性稳压器。