KTM5010B0T中文资料芯凯电子数据手册PDF规格书

Features

• USB Type-C DisplayPort Alt-mode de-mux

 Simultaneous USB3.2 Gen2 and 2 lanes DP1.4a

input OR 4 lanes DP1.4a input

 Flip option for connector plug orientation

 DP lane swap and polarity swap

• DisplayPort® (DP) ver.1.4a compliant receiver

 Link rate 1.62 / 2.74 / 5.4 / 8.1Gbps

 1, 2, or 4 lanes configuration

 MST up to 6 streams (compressed /uncompressed)

 FEC Decode

 DSC Transport & Decode

 AUX CH 1 Mbps

 HPD_OUT

 Adaptive receiver equalization

 TPS4 EQ Phase LT support

 Scrambling of main link data

 De-spreading of link frequency

 Video Stream Handling

■ RGB/ YCC 444/422/420 pixel format up

16 bpc

■ Up to 1080 Mpix/sec dual pixel path

 DPCD

■ DPCD data structure revision 1.4

■ DSC support capability & control

■ FEC capability & control

■ SST Split SDP capability

■ VSC_EXT_SDP for VESA & CTA

■ Protocol converter capability & control

■ Virtual DP Peer Device capability & control

■ CEC tunneling over AUX

 Chainable SDP packets (2KB or more metadata

per stream)

 Adaptive Sync SDP

 PPS SDPAudio stream handling

■ Non-HBR Compressed Formats

• 2/8 ch layouts

• Up to 192kHz sample rates

• Dolby Digital, Digital+, Atmos

 HBR Audio Formats

■ 8 ch layout

■ Up to 1536kHz sample rates

■ Dolby TrueHD, Atmos, DTS Master

■ LPCM Formats

■ 2/8/16/32 Ch

■ Up to 192kHz sample rates

■ 3D LPCM, speaker allocation & mapping

 OneBit DSD Formats

■ 2/8 ch

■ Single & Double Rate

■ 12288 kHz sample rates

 DST DSD Formats

■ Single/Double rate

■ Up to 22579.2kHz

 Audio InfoFrame/ ACP/ ISRC/ Audio Metadata DI

packets

• Triple DP1.4a / HDMI2.0b (DP++) transmitters

 DP mode

■ Lane count, Link rate conversion

■ Link rate 1.62 / 2.74 / 5.4 / 8.1Gbps

■ 1, 2, or 4 lanes configuration

■ DSC stream transport with FEC Encode

■ MST up to 6 streams (compressed /

uncompressed)

■ AUX CH 1 Mbps

■ 3.3V HPD_IN

 HDMI mode

■ TX1 & TX3: VML AC coupled HDMI

■ TX2: CML DC-coupled HDMI

■ No External Level shifters needed

■ 600 MHz maximum TMDS character clock

■ TMDS character-clock divide_by_4 mode

■ HPD_IN (5V Tolerant)

■ DDC CH (5V Tolerant)

• HDMI 2.1 Features

 Through 6GHz TMDS Mode

 Supports 4k120Hz,4:2:0, 8bpc with Adaptive Sync

to VRR conversion

 Dynamic HDR Metadata through Extended

Metadata Packet

 Supports VRR, FVA, QMS, QFT, ALLM

 Scrambler for DP/HDMI output

 Programmable signal amplitude and edge rate

control

 Programmable pre-emphasis control

 Pixel format RGB / YCC 444/422/420

 Deep color up to 16 bits per color

 3D video timings

 CEC support – snooping, tunneling

 SCDC read request handling

 Metadata handling

 Conversion to DVI output

 Link power management

Features (continued)

• USB3.2 compliant re-timer

 5Gbps and 10Gbps support

 Spread spectrum clocking

 LFPS polling and processing

 Lane polarity inversion

 Bit level re-timer for SS mode

 SRIS (Separate Reference Clock Independent

SSC) for SSP mode

 Adaptive Receiver Equalization

 Multi-tap FIR EQ Transmitter Emphasis

• Video processing

 MST to SST conversions or pass-through

 SST lef-right separation

 Color space conversion from RGB to YCC

 Colorimetry support: BT2020, BT709, BT601, and

Adobe RGB

 Color bit depth expansion (10 to 12 bits) 16 bits per

color pass through

 DP to HDMI Stereoscopic 3D Transport

 Frame sequential to stacked top-bottom conversion

 Pass through of other 3D formats

 Programmable coefficient 3x3 matrix

■ Programmable input offset

■ Programmable output offset

■ Programmable output clipping levels

 Chroma down sampling

■ 5-tap H & V FIR filters with programmable

coefficients

■ 12 bits per color input width

■ 12 bits per color output width

■ YCbCr444 to YCbCr420 conversion

■ YCbCr444 to YCbCr422 conversion

 Pass through for YCbCr444/422/420

 Dual DSC1.2A stream decoding

 1/2/4 Slice DSC1.2Aa RGB/YCC444/422/420 10-b

format support

 FEC decoding / encoding

 Video Horizontal blanking expansion

 Pixel stream de-skewing

 Adaptive Sync Video

• Max video resolution and color depth on DP output

uncompressed

■ 5K3K60Hz, RGB/YCbCr444, 8 bpc

■ 8K4K60Hz, YCbCr420 up to 8 bpc

■ 4K2K120Hz, RGB/YCbCr444, 8 bpc

• Max video resolution and color depth on DP output

compressed (DSC)

■ 8K4K60Hz, RGB/YCC444 up to 8 bpc

■ 5K3K60Hz, RGB/YCbCr444, 12 bpc

■ 4x 4K2K60Hz, RGB/YCbCr444, 8 bpc

• Max video resolution and color depth on HDMI TX

■ 4Kp60Hz, RGB/YCbCr444, 8 bpc

■ 4Kp60Hz, YCbCr420, up to 16 bpc

■ 4Kp30Hz, RGB/YCbCr444, up to 16 bpc

• Audio processing

 Audio stream forwarding from DP RX to HDMI TX

 Conversion to I2S or TDM audio output (8 CH)

 Conversion to SPDIF audio output (2CH)

• HDCP support

 HDCP1.3 to HDCP1.4 Repeater function

 HDCP2.3 to HDCP1.4 Repeater function

 HDCP2.3 to HDCP2.3 Repeater function

 Read- protected embedded HDCP keys

• Enhanced security

 Encrypted on-chip key storage

 RSA-2048bit signed application firmware

 Secure Boot & In-system Programming

 Test, debug ports deactivation

• Metadata handling

 HDMI TX DVI/HDMI mode setting (DPCD register)

 YCbCr444-420 conversion (DPCD register)

 IEC60958 BYTE3 channel status overwrite

 CTA861G INFO FRAME generation

 CTA861.3 HDR and Mastering InfoFrame

 Chainable VSC_EXT SDP packing format

• ARM processor and peripheral controllers

 ARM Cortex M3 core

 SPI controller

 I2C master, slave controller

 On-Chip, RAM, ROM, OTP

• Device configuration options

 Application FW stored in SPI flash

 AUX CH, I2C host interface

• Internal video pattern generator

 Configurable through vendor specific DPCD

registers

• EMI reduction support

 Spread spectrum for DP input, output

 Scrambler for DP and HDMI outputs

• Low power operation

 860mW nominal operation with retimer

 700mW nominal operation without retimer

 Under 10mW Standby operation

• ESD specification

 ESD: ±2kV HBM, 500 V CDM

• Package

 289 LFBGA (12 x 12mm)

 Halogen free Halogen free RoHS and Green

Compliant

• Power supply voltages

 1.8V Analog and I/O, 0.95V Analog and core

Description

The KTM50x0 is an advanced DisplayPort1.4a MST

hub with an integrated USB type-C de-multiplexer,

targeted primarily for Mobile Notebook accessory and

display applications. This device functions as a multistream

audio-video splitter and protocol converter with

an HDCP1.x/ HDCP2.3 repeater supporting both

compressed (DSC) and uncompressed AV streams.

KTM50x0 has a DP alt-mode capable USB Type-C

Upstream Facing Port (UFP). The four high speed

lanes of UFP can receive DP1.4a MST audio-video

and USB3.2 Gen2 data streams simultaneously. The

input lane mapping is flexible and meets standard DP

or the USB Type-C connector with flip orientation

requirements. The incoming DP and USB signals are

de-multiplexed, retimed, and transmitted on the

Downstream Facing Ports (DFP). The KTM50x0

consists of three AC coupled DP/DP++ or DC coupled

HDMI/DVI DFPs, each with four high-speed lanes and

one USB port with USB3.2 TX and RX pair. The

Stream Routing Logic in KTM50x0 allows flexible

routing of incoming DP MST stream converted into any

combination of MST or SST streams on any of the DFP

video ports with link rate and lane count change

option. Also, the SST stream can be replicated on two

or more DFP ports. In addition, the DP SST stream

can be converted into a HDMI or DVI output (TMDS

signal format).

The combo receiver in KTM50x0 supports all DP

standard data rates up to HBR3 (8.1 Gbps/lane) and

USB3.2 Gen1 (5.0 Gbps) and Gen2 (10.0 Gbps). The

dual mode (DP++) transmitters support DP standard

data rates up to 8.1 Gbps/lane and TMDS data rates

up to 6.0 Gbps/lane. The side-band channel uses 1.0

Mbps Manchester-coded AUX signaling for DP and

DDC signaling up to 100kbps for the HDMI interface.

KTM50x0 is capable of processing up to six DP audiovideo

streams compressed or uncompressed. FEC

decoding and encoding is employed for the reliable

reception and transmission of DSC1.2a compressed

streams. These streams can be part of one single

large video timing or six independent video timings

from a single source with corresponding independent

multi-channel audio. The highest video timing per

stream and the number of streams transported is

limited by the DP1.4a and HDMI2.0 link bandwidth.

When the received DP MST stream is in DSC1.2a

compressed format, KTM50x0 can decode the

streams (max two streams) or pass through to the

downstream sink or to another cascaded KTM50x0

device. If a DP source sends an 8k4k60Hz

RGB/YCC444 DSC1.2a encoded video as four

4k2k60Hz MST, then two KTM50x0 devices are

needed to decode all four streams. KTM50x0 supports

both RGB 444 and YCC444/422/420 video pixel

encoding formats with a color depth up to 16 bpc (bits

per component or 48 bits per pixel). It has a pixel

processing unit capable of video pixel encoding format

conversion from RGB444 to YCC444 with bit depth

expansion and down scaling from YCC444 to

YCC422/420. Pixel format conversion along with

horizontal blanking expansion improves

interoperability and smooth rendering of CVT video

timings from a mobile PC on a consumer displays such

as TVs and projectors which supports only CEA

timings.

KTM50x0 processes High Dynamic Range (HDR)

video content specified in BT601, BT709, BT2020,

BT2100 , Adobe RGB colorimetry format with the

proper metadata conversion from DP to HDMI. It also

offers secure reception and transmission of high

bandwidth digital audio and video content with

HDCP1.x or HDCP2.3 content protection. As a branch

device KTM50x0 functions as a HDCP1.x and

HDCP2.3 repeater between the DP source and DP or

HDMI sink.

KTM50x0 uses an external 25 MHz reference clock for

its operation. The reference clock can be generated

from a 25MHz crystal or from an external source. It has

a 300MHz ARM Cortex M3 CPU with on-chip

memories for code and data storage. The peripheral

subsystem includes SPI, UART (debug only), and I2C

master, slave interfaces. An internal Power-On Reset

(POR) circuit senses the voltage on the reset input and

provides the chip reset during system power-up. The

KTM50x0 uses an external 16 Mbit SPI flash memory

for storing the RSA-2048 signed application firmware

with fail-safe recovery. At boot up, the CPU goes

through a secure boot process authenticating the

application code image stored in the SPI flash. It

supports both standard mode and quad mode SPI

operation. Firmware update for the SPI flash is done

securely through the DP AUX_CH or I2C host

interface (Secure In-System-Programming).

Applications

The target applications of the KTM50x0 are:

• Mobile PC docking stations

• Dongles

• MST video hubs

• AR / VR devices

• High end displays such as digital signage

• Daisy-chain monitors