GL3523数据手册Genesys中文资料规格书

描述 Description

Genesys GL3523 is a 4-port, low-power, and configurable hub controller. It is compliant with the USB 3.1 specification. GL3523 integrates Genesys Logic self-developed USB 3.1 Gen 1 Super Speed transmitter/receiver physical layer (PHY) and USB 2.0 High-Speed PHY. It supports Super Speed, Hi-Speed, and Full-Speed USB connections and is fully backward compatible to all USB 2.0 and USB 1.1 hosts. GL3523 also implements multiple TT architecture providing dedicated TT to each downstream (DS) port, which guarantees Full-Speed(FS) data passing bandwidth when multiple FS devices perform heavy loading operations. Furthermore, GL3523 has built-in 5V to 3.3V and 5V to 1.2V regulators, which saves customers’ BOM cost, and eases for PCB design. GL3523 features the native fast-charging and complies with USB-IF battery charging specification rev1.2, it could fast-charge Apple, Samsung Galaxy devices, and any device complaint with BC1.2/1.1. It also allows portable devices to draw up to 1.5A from GL3523 charging downstream ports (CDP) or dedicated charging port (DCP). It can enable systems to fast charge handheld devices even during “Sleep” and “Power-off” modes.

特性 Features

Compliant with USB 3.1 Gen 1 SpecificationUpstream port supports SuperSpeed (SS), HighSpeed (HS) and FullSpeed (FS) trafficDownstream ports support SS, HS, FS, and LowSpeed (LS) traffic1 control pipe and 1 interrupt pipeBackward compatible to USB specification Revision 2.0/1.1Native USB Type-C support in GL3523-S seriesCompliant with USB Type-C Cable and Connection Specification Revision 1.0Featuring USB Type-C functionsDetecting flip-able/reversible pluggingDiscovering/configuring VBUSSupporting USB Type-C Current modes , including USB Default, 1.5A@5V, 3A@5VConfiguring/Supporting VCONN Power and having VCONN over-current protectionFeaturing fast-charging on all downstream ports and upstream portCompliant with USB Battery Charging Revision v1.2, supporting CDP, DCP, and ACA-DockDownstream ports can be turned from a Standard Downstream Port (SDP) into Charging Downstream Port (CDP) or Dedicated Charging Port (DCP)Downstream devices can be charged while upstream VBUS is not present, which can be applied on wall charger applicationsUpstream port is capable of charging and data communicating simultaneously for portable devices supporting ACA-Dock or proprietary charging protocolsSupporting Apple 1A/2.1A/2.4A and Samsung Galaxy devices fast-chargingOn-chip 8-bit micro-processorRISC-like architectureUSB optimized instruction set1 cycle instruction execution (maximum)Performance: 12 MIPS @ 12.5MHz (maximum)With 256-byte RAM, 20K-byte internal ROM, and 24K-byte SRAMMultiple Transaction Translator (TT) architectureProviding dedicated TT control logics for each downstream portSuperior performance when multiple FS devices operate concurrentlyIntegrated USB transceiverImproving output drivers with slew-rate control for EMI reductionInternal power-fail detection for ESD recoveryAdvanced power management and low power consumptionSupporting USB 3.1 U0/U1/U2/U3 power management statesSupporting USB Link Power Management (LPM) L0/L1/L2Supporting individual/gang mode over-current detection for all downstream portsSupporting both low/high-enabled power switchesPatented Smart Power ManagementConfigurable settings by firmware in SPI flashConfigurable charging portConfigurable 4/3/2 downstream ports, downstream port can be disabled/enabled by each specific port for USB3.1/USB2.0Configurable Upstream and Downstream Ports in GL3523-SSupporting multiple upstream ports in GL3253-S OV3S1 and OV5S1 packagesSupporting full in-system programming firmware upgrade by SPI-flash and configuration by EEPROMSupporting compound-device (non-removable setting on downstream ports)Supporting customization VID/PIDFlexible designSupporting Poly-fuse/Power-switchAutomatic switching between self-powered and bus-powered modesSupporting electrical tuning for each specific portSupporting programmable breathing LEDSupporting register setting by firmwareSupporting vendor command and SMBUSAllow downstream ports to connect up to 8 devices, 4 x USB3.1 non-removable devices with 4 x USB2.0 non-removable devices or exposed portsLow BOM costSingle external 25 MHz crystal / Oscillator clock inputBuilt-in upstream port 1.5KΩ pull-up and downstream port 15KΩ pull-down resistorsBuilt-in 5 to 3.3V and 5 to 1.2V regulatorDifferent package types available for various applicationsApplicationsStandalone USB hub/Docking stationTablet/Ultrabook/NBMotherboardMonitor built-in hub, GPIOs can be programmed as I2C interface to easily update scalar firmware through USB interfaceTV built-in hubCompound device, such as hub-reader applicationUSB wall chargerOther consumer electronicsCustomized applicationsDynamically disable/enable portsGPIO signaling of ambient light sensor or rotation/position sensor