ePS5001数据手册Elan中文资料规格书

描述 Description

The ePS5001 is an 8-bit RISC MCU embedded with a 5 x 40 LCD driver along with two
8-bit timers, one 16-bit general timer, and a watchdog timer. It has also an on-chip 128
bytes RAM and 2K words program ROM. It is highly ideal for advance scientific calculator
application, particularly those requiring high performance and low cost solution.
The MCU core is one of ELAN's second generation RISC based IC's, known as RISC II
(RII) series. The core was specifically designed for low power and portable device
applications. The ePS5001 also supports Fast, Slow, and Idle modes, as well as Sleep
mode to enhance its low power consumption features.IMPORTANT NOTES  Do not use Register BSR (05h) Bit 7 ~ Bit 0. Do not use Register BSR1 (07h) Bit 7 ~ Bit 0.  Check the range of BSR (05h) and BSR1 (07h) are only 0x00.  Do not use LCD RAM 28h ~ FFh. Do not useJDNZ at FSR1 (04h) special register. Do not useJDNZ at LCDARL (09h) special register. Do not use PUSH, POP by \"MOV A,r\" to avoid affecting S_Z.

特性 Features

MCU 8 bit RISC MCU
Operating voltage: 1.2V ~ 1.8V
Clock Source: Dual system clock
*  Low-frequency: 32kHz Internal RC oscillator / Crystal oscillator
*  High-frequency: 200kHz / 300kHz / 500kHz External RC oscillator
One Instruction cycle time = 2 x System clock time
Program ROM addressing: 2K words max.
128 bytes un-banked RAM & Working RAM
128 bytes un-banked RAM including special registers and common registers
1 x 128 bytes banked RAM
Max of 32-level RAM stack
Table Lookup function is fast and efficient when combined with Repeat instruction
Register-to-Register move instruction
Compare and Branch in one instruction (two cycles)
Single Repeat function (256 max. repeat times)
Decimal ADD & SUB instruction
Full range CALL and JUMP ability (two cycles)
Peripheral4 input pins (Port A.0~3) and 12 general I/O pins (Port A.4~7, Port B.0~7)
5/4/3 COM x 40 SEG LCD driver (embedded)
One 16-bit timer (Timer 0) with Event counter function
One 8-bit timer (Timer 1) with wake-up function
One 8-bit timer (Timer 2)
One 8-bit Watchdog Timer
Key I/O function with a maximum of 48 keys (Key matrix: Port A.0~2 and SEG0~15 with automatic key scan)
Internal Specification
Watchdog Timer with its own on-chip RC oscillator
MCU operating modes: Sleep Mode, Idle Mode, Slow Mode, and Fast Mode
Supports RC oscillation and crystal oscillation for system clock
MCU Wake-up function consists of input wake up and Timer 1 wake up
MCU interrupt function consists of Input port interrupt and Timer interrupt(Timers 0 ~ 2)
MCU reset function includes power-on reset, RSTB pin reset, and Watchdog Timer reset

应用 Application

. The ePS5001 also supports Fast, Slow, and Idle modes, as well as Sleep mode to enhance its low power consumption features.IMPORTANT NOTES  Do not use Register BSR (05h) Bit 7 ~ Bit 0.
 Do not use Register BSR1 (07h) Bit 7 ~ Bit 0.
 Check the range of BSR (05h) and BSR1 (07h) are only 0x00.
 Do not use LCD RAM 28h ~ FFh.
 Do not useJDNZ at FSR1 (04h) special register.
 Do not useJDNZ at LCDARL (09h) special register.
 Do not use PUSH, POP by \"MOV A,r\" to avoid affecting S_Z.