dsPIC33FJ256GP506

High-Performance, 16-Bit Digital Signal Controllers; Operating Range:• DC – 40 MIPS (40 MIPS @ 3.0-3.6V, -40°C to +85°C)• Industrial temperature range (-40°C to +85°C)High-Performance DSC CPU:• Modified Harvard architecture• C compiler optimized instruction set• 16-bit wide data path• 24-bit wide instructions• Linear program memory addressing up to 4M instruction words• Linear data memory addressing up to 64 Kbytes• 83 base instructions: mostly 1 word/1 cycle• Sixteen 16-bit General Purpose Registers• Two 40-bit accumulators:- With rounding and saturation options• Flexible and powerful addressing modes:- Indirect, Modulo and Bit-Reversed• Software stack• 16 x 16 fractional/integer multiply operations• 32/16 and 16/16 divide operations• Single-cycle multiply and accumulate:- Accumulator write back for DSP operations- Dual data fetch• Up to ±16-bit shifts for up to 40-bit dataDirect Memory Access (DMA):• 8-channel hardware DMA:• 2 Kbytes dual ported DMA buffer area (DMA RAM) to store data transferred via DMA:- Allows data transfer between RAM and a peripheral while CPU is executing code (no cycle stealing)• Most peripherals support DMAInterrupt Controller:• 5-cycle latency• 118 interrupt vectors• Up to 67 available interrupt sources• Up to 5 external interrupts• 7 programmable priority levels• 5 processor exceptionsDigital I/O:• Wake-up/Interrupt-on-Change on up to 24 pins• Output pins can drive from 3.0V to 3.6V• All digital input pins are 5V tolerant• 4 mA sink on all I/O pinsSystem Management:• Flexible clock options:- External, crystal, resonator, internal RC- Fully integrated PLL- Extremely low jitter PLL• Power-up Timer• Oscillator Start-up Timer/Stabilizer• Watchdog Timer with its own RC oscillator• Fail-Safe Clock Monitor• Reset by multiple sourcesPower Management:• On-chip 2.5V voltage regulator• Switch between clock sources in real time• Idle, Sleep and Doze modes with fast wake-upTimers/Capture/Compare/PWM:• Timer/Counters, up to nine 16-bit timers:- Can pair up to make four 32-bit timers- 1 timer runs as Real-Time Clock with external 32.768 kHz oscillator- Programmable prescaler• Input Capture (up to 8 channels):- Capture on up, down or both edges- 16-bit capture input functions- 4-deep FIFO on each capture• Output Compare (up to 8 channels):- Single or Dual 16-Bit Compare mode- 16-bit Glitchless PWM modeCommunication Modules:• 3-wire SPI (up to 2 modules):- Framing supports I/O interface to simple codecs- Supports 8-bit and 16-bit data- Supports all serial clock formats and sampling modes• I2C™ (up to 2 modules):- Full Multi-Master Slave mode support- 7-bit and 10-bit addressing- Bus collision detection and arbitration- Integrated signal conditioning- Slave address masking• UART (up to 2 modules):- Interrupt on address bit detect- Interrupt on UART error- Wake-up on Start bit from Sleep mode- 4-character TX and RX FIFO buffers- LIN bus support- IrDA® encoding and decoding in hardware- High-Speed Baud mode- Hardware Flow Control with CTS and RTS• Data Converter Interface (DCI) module:- Codec interface- Supports I2S and AC’97 protocols- Up to 16-bit data words, up to 16 words per frame- 4-word deep TX and RX buffers• Enhanced CAN (ECAN™ module) 2.0B active (up to 2 modules):- Up to 8 transmit and up to 32 receive buffers- 16 receive filters and 3 masks- Loopback, Listen Only and Listen All Messages modes for diagnostics and bus monitoring- Wake-up on CAN message- Automatic processing of Remote Transmission Requests- FIFO mode using DMA- DeviceNet™ addressing supportAnalog-to-Digital Converters (ADCs):• Up to two ADC modules in a device• 10-bit, 1.1 Msps or 12-bit, 500 Ksps conversion:- 2, 4 or 8 simultaneous samples- Up to 32 input channels with auto-scanning- Conversion start can be manual or synchronized with 1 of 4 trigger sources- Conversion possible in Sleep mode- ±2 LSb max integral nonlinearity- ±1 LSb max differential nonlinearityCMOS Flash Technology:• Low-power, high-speed Flash technology• Fully static design• 3.3V (±10%) operating voltage• Industrial temperature• Low-power consumption;

dsPIC33F General Purpose Digital Signal Controller (DSC) with seamless migration options to PIC24 MCUs and dsPIC30F DSCs in similar packages.

DSPIC33FJ256GP506

Silicon Errata

DSPIC33FJ256GP506

Flash Programming Specification

DSPIC33FJ256GP506

High-Performance,16-Bit Digital Signal Controllers

DSPIC33FJ256GP506

High-Performance, 16-Bit Digital Signal Controllers

DSPIC33FJ256GP506

High-Performance 16-Bit Digital Signal Controllers

dsPIC33FJ256GP506A

16-Bit Digital Signal Controllers; Operating Conditions Up to 40 MIPS operation\n3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS \n• 3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS \nHigh-performance dsPIC33F core• Code-efficient (C and Assembly) architecture \n• Two 40-bit wide accumulators \nSingle-cycle (MAC/MPY) with dual data fetch \nSingle-cycle mixed-sign MUL plus hardware divide \nClock Management • Programmable PLLs and oscillator clock sources \n• ±2% internal oscillator \n• Fail-Safe Clock Monitor (FSCM) \n• Independent Watchdog Timer (WDT) \n• Fast wake-up and start-up \nPower Management • Low-power management modes (Sleep, Idle, Doze) \n• Integrated Power-on Reset and Brown-out Reset \n• 2.1 mA/MHz dynamic current (typical)\n• 50 μA IPD current (typical)\nAdvanced Analog Features Two ADC modules: - Configurable as 10-bit, 1.1 Msps with four S&H or 12-bit, 500 ksps with one S&H - 18 analog inputs on 64-pin devices and up to 32 analog inputs on 100-pin devices \n• Flexible and independent ADC trigger sources\nTimers/Output Compare/Input Capture • Up to nine 16-bit timers/counters (Can pair up to make four 32-bit timers)\n• Eight Output Compare modules configurable as timers/counters \n• Eight Input Capture modules Communication Interfaces \n• Two UART modules (10 Mbps) - With support for LIN 2.0 protocols and IrDA® \n• Two 4-wire SPI modules (15 Mbps) \n• Up to two I2C™ modules (up to 1 Mbaud) with SM Bus support \nEnhanced CAN (ECAN) module (1 Mbaud) with CAN 2.0B support\n• Data Converter Interface (DCI) module with I2S codec support\nInput/Output • Sink/Source up to 10 mA (pin specific) for standard VOH/VOL, up to 16 mA (pin specific) for non-standard VOH1\n• 5V-tolerant pins \n• Selectable open drain, pull-ups, and pull-downs \n• Up to 5 mA overvoltage clamp current \n• External interrupts on all I/O pins \nDebugger Development Support • In-circuit and in-application programming \n• Two program and two complex data breakpoints \n• IEEE 1149.2-compatible (JTAG) boundary scan\n• Trace and run-time watch;

•dsPIC33Fs are designed to execute digital filter algorithmsand high-speed precision digital control loops, ideal for applications thatneed to perform under pressure           •GeneralPurpose Digital Signal Controllers (DSCs) with advanced analog and seamlessmigration options to PIC24F, PIC24H MCUs and dsPIC30F DSCs

DSPIC33FJ256GP506A

High-Performance, 16-bit Digital Signal Controllers

DSPIC33FJ256GP506A

16-bit Digital Signal Controllers (up to 256 KB Flash and 30 KB SRAM) with Advanced Analog

dsPIC33FJ256GP506A

16-bit Digital Signal Controllers (up to 256 KB Flash and 30 KB SRAM) with Advanced Analog