AT91SAM9CN12数据手册集成电路（IC）的微处理器规格书PDF

描述 Description

The Microchip's ARM®-based SAM9CN12 is an ARM926EJ-S -based MPU that provides secure boot, an encryption engine, user interface functionality and high data rate connectivity. Plus it offers power efficiency and reduced BOM cost, making it the ideal solution for cost-sensitive industrial applications that require security features in addition to graphics LCD and user interface software functionality.

特性 Features

ARM926EJ-S ARM® Thumb® Processor running up to 400 MHz
16 Kbytes Data Cache, 16 Kbytes Instruction Cache, Memory Management Unit Memories
One 128-Kbyte internal ROM embedding standard or secure bootstrap routine
One 32-Kbyte internal SRAM, single-cycle access at system speed
32-bit External Bus Interface supporting 8-bank DDR2/LPDDR, SDR/LPSDR, Static Memories
MLC/SLC NAND Controller, with up to 24-bit Programmable Multibit Error Correction Code (PMECC) System running up to 133 MHz
Power-on Reset, Reset Controller, Shutdown Controller, Periodic Interval Timer, Watchdog Timer and Real Time Clock
Boot Mode Select Option, Remap Command
Internal Low Power 32 kHz RC and Fast 12 MHz RC Oscillators
Selectable 32768 Hz Low-power Oscillator, 16 MHz Oscillator, one PLL for the system and one PLL optimized for USB
Six 32-bit-layer AHB Bus Matrix
Dual Peripheral Bridge with dedicated programmable clock
One dual port 8-channel DMA Controller
Advanced Interrupt Controller (AIC)
Two Programmable External Clock Signals
Low-power Mode
Shutdown Controller with four 32-bit General-purpose Backup Registers
Clock Generator and Power Management Controller
Very Slow Clock Operating Mode, Software Programmable Power Optimization Capabilities
LCD Controller
USB Device Full Speed with dedicated On-chip Transceiver
USB Host Full Speed with dedicated On-chip Transceiver
One High-speed SD card and SDIO Host Controller
Two Master/Slave Serial Peripheral Interfaces (SPI)
Two 3-channel 32-bit Timer/Counters (TC)
One Synchronous Serial Controller (SSC)
One 4-channel 16-bit PWM Controller
Two 2-wire Interfaces (TWI)
Four Universal Synchronous Asynchronous Receiver Transmitters (USART)
Two Universal Asynchronous Receiver Transmitters (UART)
One Debug Unit (DBGU)
One 12-channel 10-bit Analog-to-Digital Converter with up to 5-wire resistive Touchscreen support
Crystal Failure Detection
Independent Watchdog
Power-on Reset Cells
Register Write Protection
SHA (SHA1 and SHA256) Compliant with FIPS Publication 180-2 (SAM9CN11/SAM9CN12 devices)
True Random Number Generator (TRNG) compliant with NIST Special Publication 800-22
AES 256-, 192-, 128-bit Key Algorithm compliant with FIPS Publication 197 (SAM9CN11/SAM9CN12 devices)
256 Fuse bits for crypto key and 64 Fuse bits for device configuration, including JTAG disable and forced boot from the on-chip ROM (Secure Boot feature - SAM9CN12 only)
Four 32-bit Parallel Input/Output Controllers
105 Programmable I/O Lines Multiplexed with up to Three Peripheral I/Os
Input Change Interrupt Capability on Each I/O Line, optional Schmitt Trigger input
Individually Programmable Open-drain, Pull-up and Pull-down Resistor, Synchronous Output
217-ball BGA, pitch 0.8 mm
247-ball BGA, pitch 0.5 mm

简介

AT91SAM9CN12属于集成电路（IC）的微处理器。由制造生产的AT91SAM9CN12微处理器微处理器产品是用于信息和数据处理的集成电路。与主要按照制造商所选术语而视为微控制器的类似产品相比，这些器件有所不同。但是按照传统，微处理器不会在设备内集成工作存储器，不太可能集成混合信号外设，并且可能在更为复杂的软件范式下使用，这些范式涉及使用操作系统来管理多任务同时执行。